In some circumstances (e.g. inappropriate jtag clock)
target_write_memory in lpc2000_iap_working_area_init might fail. The
allocated working area should be freed inside
lpc2000_iap_working_area_init in this error case.
This was leading to a weird segfault due to stack corruption later
when reset was executed.
Reported by quitte (Jonas Meyer).
Change-Id: Ia2ed42a9970a4d771727fd516a6eea88e9b859e2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2696
Tested-by: jenkins
The IAP working area needs to be freed here, just like in all the
other driver functions since an automatic local variable is used to
store a pointer to it.
This was reported by quitte (Jonas Meyer) on IRC as a strange totally
unrelated segfault after doing certain operations (leading to target
reset) from GDB. He has provided me with remote access to the specific
machine and configuration that exposed the issue, and after some
debugging it became apparent that a auto local variable (holding the
gdb connection pointer) gets overwritten somehow. Placing an
appropriate breakpoint just before the event and using a watchpoint
made the cause apparent: reset lead to freeing of all working areas,
and there was one holding a pointer to a variable that was auto local
in get_lpc2000_part_id().
Change-Id: I7e634d890135ca0f3b4b311e09e8385a03982bd6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2695
Tested-by: jenkins
Current flash driver can fail to write across the sector boundary.
This patch fixes "thisrun_bytes" set to "cmd51_dst_boundary" value instead of "cmd51_can_xxxxb"
Referred to SevenW's post and fix,thanks.
http://sourceforge.net/p/openocd/mailman/openocd-devel/thread/fa32e7d6654df22470dc5f4a3dbc984a%40familiebenschop.nl/#msg33594152
Tested on below listed chips.
LPC810,LPC811,LPC812,LPC824,LPC1115,LPC1343,LPC1347,LPC1227,
LPC1769,LPC1788,LPC54102,LPC4088 and LPC2388.
Change-Id: If1c6a1daa58ca27c405bd959a784e599a7a8f4d4
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2607
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I53568674951ec8a5db5e191c7b50c60b5a84d0b6
Signed-off-by: Michael Brown <fractalmbrown@gmail.com>
Reviewed-on: http://openocd.zylin.com/2463
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds flash programming support for LPC5410x and LPC82x.
And adds auto flash size detection for LPC800 series.
Tested on below listed boards/chips.
LPC54102(LPCLPC54102Xpresso)
LPC824(LPCXpresso824-MAX)
LPC812(LPC812MAX)
LPC811,LPC810
Change-Id: Ie68b6d425b17ccfa83814607ee61056e99800c1c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2442
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The IAP firmware won't return a proper status with some versions. This
happens on my CCC r0ket board and others have seen it as well [1]. So
just ignore the status code and do a (weak) consistency check instead.
[1] http://www.lpcware.com/content/forum/lpc1343-iap-read-part-identification-command
Change-Id: I0daa779d520a540629677c56857bbc20d6db422d
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Reviewed-on: http://openocd.zylin.com/2364
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds flash programming support for LPC1547/8/9 and LPC1517/8/9.
Tested on LPC1549(LPC1549 LPCXpresso Board with CMSIS-DAP firmware).
Change-Id: Ic95b4d62055bb9fdc2ca484696a38ccaf49ad951
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2304
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Grigori G <greg@chown.ath.cx>
Adds support for auto-probing on devices which support the IAP
Read Part ID command. Includes IDs for all LPC17XX, LPC13XX,
LPC11XX and LPC11XXX devices with publicly available user
manuals.
To use auto-probing, select the 'auto' lpc2000 variant.
Change-Id: Ic617c32925c9ebe0e9d9192ed8ddbfa08e9f0aaa
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2075
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
LPC11(x)xx and LPC13xx devices are mostly compatible with the lpc1700
variant of the LPC2000 driver, but use a fixed flash sector size of 4KB.
Change-Id: I033515f4ff6bc61d3b9babd27096f78c99cea927
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2071
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
IAP commands fail on programming LPC810 because it has only 1kByte of SRAM.
This patch is fixing cmd51_max_buffer suitable size for LPC810,LPC811 and
other LPC1000 series.
Tested on a LPC810,LPC812,LPC11u14,and LPC1114(DIP28).
Change-Id: Iecec9fd963cb63bdff4a7bd3bbf4f8b1a7c60fbd
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/1843
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This eliminates most of the warnings reported when building for
arm-none-eabi (newlib).
Hsiangkai, there're many similar warnings left in your nds32 files, I
didn't have the nerve to clean them all, probably you could pick it
up.
Change-Id: Id3bbe2ed2e3f1396290e55bea4c45068165a4810
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1674
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
some members of lpc2000_info structure sometimes used uninitialized
(cmd51_can_64b for all LPC except LPC800 as example).
Init allocated lpc2000_info structure with zeros to avoid this and similar bugs in the future.
Note: maybe discarding all cmd51_can_XXXb fields and using cmd51_dst_boundary instead will be a better solution.
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Change-Id: Idf116a5b0bf4ea1c39ea0ce308ec2c13bfbd4d8c
Reviewed-on: http://openocd.zylin.com/1676
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
This patch adds flash programming support for internal flash of the
LPC43x2/3/5/7 part, tested on a LPC4337 (also tested on a LPC1768
and LPC2468). It should also work with LPC1800's with onchip flash.
The "base" parameter of the "flash bank" command is now significant
for the lpc4300 variant and required to determine the bank number
parameter needed by the IAP routines.
NOTE: I could only program flash successfully when the chip is powered
with "P2_7" pulled low to put it in ISP mode. When running from flash
(and not the ISP ROM), the target fails to halt and the sector erase
fails. This is similar to the behavior I remember when trying out the
spifi driver on a LPC4350... lots of power cycles to make progress, one
To burn, one to run. So I am not confident my config is set up correctly.
Change-Id: I8a75ef1b95cedd5b5898b2dedff477f502fd19f3
Signed-off-by: Matt Dittrich <mdittrich.dev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1126
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
This makes sure we are using privileged mode when executing any loaders.
Change-Id: I18bf32ec92e1c76a66ab25e3712652bc3650b332
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1108
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
To simplify things change over to using the generic core_mode struct rather
than maintaining a armv7m specific one.
Change-Id: Ibf32b785d896fef4f33307fabe0d8eb266f7086f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/966
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Flash algorithm for LPC17xx/LPC2xxx was trying to "reuse" previously
allocated working area on next flashing which is not possible -
working areas are freed automatically on reset. This caused all but
first flashing attempts to fail. As there is no point in storing pointer
to working area, it was converted to local variable.
Change-Id: I939946325ff9eecc4861c0f51ab0f73871a3d7b9
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/860
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Do some cleanup in lpc2000.c - concatenate short lines into single
longer lines, move variable declarations to "just before" they are
used, etc.
Change-Id: Ia7b9f0307dd4857ee8e15c8a6d4d7b5c4392fd80
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/861
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
By Initialising the param_table we remove the clang warning's.
We are also make sure we are not passing any rogue values to lpc2000_iap_call.
Change-Id: Idb3b0077d1dae5f03dedab1d46d01140fe9ffb10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/777
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This makes the code a bit easier to read as arm_algorithm can
refer to other arch's, not just armv4_5.
Change-Id: I78c99d40f34cda04e06f2daee75b48ff40a1d23d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/613
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On wrong parameters a error is signalized to the calling function.
Change-Id: I484443fdb39938e20382edc9246d5ec546a5c960
Signed-off-by: Mathias K <kesmtp@freenet.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/282
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
For the above targets the exit_point is
optional when used with run_algorithm, so remove it.
This makes updating the algorithm less error prone.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Final target is to force bus_width size during CFI flash
read.
In this first step I need to replace default flash read
with flash specific implementation.
This patch introduces:
- flash_driver_read() layer;
- default_flash_read(), backward compatible;
- read() callback in struct flash_driver;
- proper initialization in every flash_driver instance.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fix some issues with the generic LPC1768 config file:
- Handle the post-reset clock config: 4 MHz internal RC, no PLL.
This affects flash and JTAG clocking.
- Remove JTAG adapter config; they don't all support trst_and_srst
- Remove the rest of the bogus "reset-init" event handler.
- Allow explicit CCLK configuration, instead of assuming 12 MHz;
some boards will use 100 Mhz (or the post-reset 4 MHz).
- Simplify: rely on defaults for endianness and IR-Capture value
- Update some comments too
Build on those fixes to make a trivial config for the IAR LPC1768
kickstart board (by Olimex) start working.
Also, add doxygen to the lpc2000 flash driver, primarily to note a
configuration problem with driver: it wrongly assumes the core clock
rate never changes. Configs that are safe for updating flash after
"reset halt" will thus often be unsafe later ... e.g. for LPC1768,
after switching to use PLL0 at 100 MHz.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
- armv7m_run_algorithm now requires all algorithms to use
a software breakpoint at their exit address
- updated all algorithms to support this
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Move the ARM opcode macros from <target/armv4_5.h>, and a few
Thumb2 ones from <target/armv7m.h>, to more appropriate homes
in a new <target/arm_opcodes.h> file.
Removed duplicate opcodes from that v7m/Thumb2 set. Protected
a few macro argument references by adding missing parentheses.
Tightening up some of the line lengths turned up a curious artifact:
the macros for the Thumb opcodes are all 32 bits wide, not 16 bits.
There's currently no explanation for why it's done that way...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "armv7m.h"
the following form should be used.
#include <target/armv7m.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "algorithm.h"
the following form should be used.
#include <target/algorithm.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "binarybuffer.h"
the following form should be used.
#include <helper/binarybuffer.h>
The exception is from .c files in the same directory.
