This driver provides support for the P&E Micro OSBDM adapter (sometimes
named as OSJTAG), mounted on the Freescale TWRK60N512 bord. Thus, it
provides a quick start when working with this board. The driver doesn't
use BDM commands, but work with OSBDM adapter using only JTAG commands.
Change-Id: Ibc3779538e666e07651d3136431e5d44344f3b07
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-on: http://openocd.zylin.com/492
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced 7 new Cortex-M3 processors on 2012-02-28
SAM3X4C - 256KB flash
SAM3X4E - 256KB flash
SAM3X8C - 512KB flash
SAM3X8E - 512KB flash
SAM3X8H (Only on dev-kit - not in production...) - 512KB flash
SAM3A4C - 256KB flash
SAM3A8C - 256KB flash
The SAM3X/A processors still suffer from the "6 waitstates needed
to program device" errata.
The CIDR address for the SAM3X/A processors are different from the
other SAM3 processors. Unfortunately, the chip identification register
is not at a constant address across all of the SAM3 series'. As a
consequence, a simple heuristic is used to find where it's
at... If the contents at the first address is zero, then we know
that the second address is where the chip id register is.
We can deduce this because for those SAM's that have the chip id @ 0x400e0940,
the first address, 0x400e0740, is located in the memory map of the Power
Management Controller (PMC). Furthermore, the address is not used by the PMC.
So when read, the memory controller returns zero.
Another interesting change is the flash bank address for flash bank 1.
It is not fixed at 0x00100000 like the Sam3U. Bank 1 of the at91sam3a/x
series starts at 0x00080000 + half the total flash size. Thus for the 256KB
devices Bank 1 is located at 0x000A0000, and for the 512KB devices Bank 1 is
located at 0x000C0000.
The configuration files for the SAM3X/A processors will follow
Change-Id: I6c3a707c00e05d993a2ad1d5a423f23b37ffd553
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/505
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
arm7_9_prepare_reset_halt is long since gone and the functionality
is implemented in the target's assert_reset handler.
Change-Id: Ib03c730cb39d68e5e3bb42f92af13daf8074e4e2
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/515
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.
Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
target_call_event_callbacks needs to be called after debug entry otherwise
we will get a console pc mismatch.
Change-Id: I278137736d5e85ca9662c306f6ac81336d8eb6cf
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/499
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The SUPC (Supply Controller) registers are on different base addresses on different
SAM3 chips:
SAM3U: 0x400e1210
SAM3N: 0x400e1410
SAM3S: 0x400e1410
This creates a problem with the sam3_reg_list array which is const, but would need
to be changed at runtime to account for this variability. As this register is not
used anywhere, it's simplest to just remove it.
Change-Id: I987eb371648d826aa6d5e9de18d38c7bb66d6fca
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/495
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Lock region count and sector sizes did not match datasheet.
(see 6500C-ATARM-8FE11 "SAM3S Series Datasheet", Table 7-1)
Change-Id: Ic511802f96ed03856467a24a6736349205a0576a
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/493
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
implement stlink_usb_send and use it to fix stlink_usb_write_mem
using two calls to stlink_usb_recv is inappropriate since each
call issues a SG command on stlink-v1, resulting in errors
Change-Id: I24ef9f2dda284e041dc4a532b59968a77eebe702
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/498
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
I committed in the wrong order
This reverts commit 79230a8e3c5b85601fca730dfc09ecc52e693afa
Change-Id: Iace872ac4844891f4f38fca87448a2ebd9f17593
Reviewed-on: http://openocd.zylin.com/497
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch moves the bulk of the stlink read/write code into the
stlink_usb_xfer set of functions and implements stlink_usb_recv
in terms of the generic stlink_usb_xfer
stlink_usb_xfer will be needed to implement stlink_usb_send
without code duplication
stlink_usb_xfer:
-sends the stlink command
-performs a read or write (as requested)
-checks the status (v1 only)
Change-Id: I0137d52620bd4883d46c9977a9e73f67622000a1
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/477
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The assert introduced in 00c8648351 checks
whether the programming offset equals to page_size of the flash, while it
wants to check whether the offset is a multiple of the page_size.
Change-Id: I794d021951a28c1cc520b5eea5d500f097721b06
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/482
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Currently stm32lx flash driver will remove the readout protection if set
during a probe.
This may not be what the user wants, so let them decide.
Change-Id: I8575e3b339b10a4f7bac57cca9586dcab513d347
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/465
Tested-by: jenkins
implement stlink_usb_send and use it to fix stlink_usb_write_mem
using two calls to stlink_usb_recv is inappropriate since each
call issues a SG command on stlink-v1, resulting in errors
Change-Id: I52ff9ee8f5d9ae0d47356477468eb98952205c99
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/478
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Split out functions specific to the AM335x SOC into the target directory and simplified the board config
file. This should allow one to quickly create new configs for boards based on the TI processor family.
Change-Id: I0c3db97950dfa832f1f1918fc10c180f068bba74
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Reviewed-on: http://openocd.zylin.com/489
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Simplified the configuration and removed things that were not necessary for debugging. Also added reset
configuration.
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Change-Id: I96f991c3051aa68278212cd6509484cbce40ccb7
Reviewed-on: http://openocd.zylin.com/488
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
when -ignore-version is used we should mask of the upper 4bits not 8bits.
Change-Id: I9ffe24c2aeeb414677357a647609fdf018890194
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/473
Tested-by: jenkins
This fixes scan_chain to correctly print all the expected_ids.
Change-Id: I93738980d85e0fe369d40c58b19339424d37ec34
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/474
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This enable the stm32f2x flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 1048576 bytes from file stm32f4x.bin in 30.453804s (33.625 KiB/s)
after - wrote 1048576 bytes from file stm32f4x.bin in 23.679497s (43.244 KiB/s)
This also fixes a bug that was in the old flash loader.
The old loader waited while bit16 of the status reg was 0, the new
loader waits until this bit is 0 as stated in the flash spec.
Bizarrely this bug did not effect programming on any tested parts.
Change-Id: I3efc94d42cbe81283673a8f4203700638080af6e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/460
Tested-by: jenkins
This enable the Stellaris flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 65536 bytes from file test.bin in 5.486040s (11.666 KiB/s)
after - wrote 65536 bytes from file test.bin in 2.274001s (28.144 KiB/s)
Change-Id: I9004c9aadffa1ae3b0cbf908e6549b5b1f794508
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/403
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Currently the stm32f1x flash driver uses an asynchronous algorithm
as part of the block flash programming. This greatly speeds up flash
programming as the target is always running.
Moving the async code to the target enable other targets to use this
added functionality.
Change-Id: I8e53f094c2ef7848a7f86ddb9a35b6edbfc8454a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/402
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Moved ti_beaglebone.cfg to the board configuration directory. This was
originally placed in the wrong location.
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Change-Id: I05d10b62b1a21618635ee1773c30d77dc756ec82
Reviewed-on: http://openocd.zylin.com/481
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for the Beaglebone board based on the am335x processor
family. After much trial and error, I was able to configure the
Icepick-D and connect to the processor, halt execution, and run a sample
program. This is a unified config file (it doesn't use any include
statements) and further work needs to be done to split out the icepick-d
configuration to be more generic.
Change-Id: Ia1b8e9f01f56bd4f8c575ba3d0160c248583a15e
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Reviewed-on: http://openocd.zylin.com/471
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a much cleaner solution to the problem of allocating as much
working area as possible than what is currently being done in most/all flash
drivers (which is: try an arbitrary sized chunk, if it fails, pick a smaller
number, rinse and repeat).
Use this function to find out how much working area is available, limit or
restrict that amount at will and then simply allocate it.
Change-Id: Ib7d5d0b7485aed3e0a4fad60c1bedb7dfd16146f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/446
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The existing allocator couldn't reuse a freed allocation if the sizes
didn't match exactly. That led to problems when for example a flash write
routine had allocated all of the working area to speed up operation. A
subsequent verify pass couldn't allocate space for the checksum algorithm
even though all previous allocations had been freed.
This allocator is marginally more complex, but solves the above problem by
splitting larger free areas to fulfill smaller requests and by merging
released areas into adjacent free areas.
An initial free area, covering the entire specified address range, is set
up on first allocation, and all allocations are split off from (and
ultimately merged into) that one. It can also easily be adapted to support
several disjoint working areas for the same target, by setting up several
initial free areas and slightly modifying the merge code.
Change-Id: I6faaf9801312bb19a4fa4474694a0cd1c6e0ab54
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/445
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The stm32 family supports using SYSRESETREQ as a software reset, lets
use it.
Change-Id: I171ffa8d888a2d0c28b266051030311521e9bca9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/472
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
This brings the stlink driver inline with the rest of OpenOCD.
If the user configures the tap as -expected-id 0 then the IDCODE will be
treated as a wildcard and ignored.
Change-Id: I99160c69b2b40f5b1f608bb59ab6630894502fd8
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/476
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
A period or comma must follow the closing brace of an @xref.
Change-Id: Ida5dc3600eca328d95b0a8f6b5c9fe0a0f3ba820
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/475
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
This patch add the status check.
Change-Id: I0fdb9bf66dad5ae416c7aa4c6e19116f846571f9
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/463
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This sets the default stellaris working area to 2k rather than
the current 8k. 2K is the smallest RAM size in the stellaris family.
Change-Id: I1407f758eb0926cc094b824a6d25199b313c45de
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/458
Tested-by: jenkins
A period or comma must follow the closing brace of an @xref.
Change-Id: I272f1e7fac8f1fee4844f485b0b8e2e4e9cf352d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/456
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
automake 1.11.2 throws `pkglibdir' is not a legitimate directory for `DATA'
if nobase_dist_pkglib_DATA is used.
We work around this issue by defining our own location.
Change-Id: I3c29e2df0b67e745283c50d358e31699bd60dc74
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/457
Tested-by: jenkins
I used the CPUID instead of adding a new argument to the flash bank command
Fixed Type in comments
Add the failsafe return value in device_id
Change-Id: Ieb5a46fc002b5390a0c81bc8b49f6c687036ae1d
Signed-off-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-on: http://openocd.zylin.com/438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add the bootloader define.
Change-Id: I280a8a35c3514910dd381de3ab8ad59c9bd74ca1
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/455
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ref manuals for the stm32f2x (RM0033 Rev4) and stm32f4x (RM0090 rev1)
are unclear to the address of the flash size register (F_ID).
According to contacts @ ST this is the correct address, the manuals will be
updated in due coarse.
Change-Id: If9fb83b3100458d17038cf27c2b23355e1dc5a9e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/448
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
