With extra / the directory was getting added as a subdirectory of
itself.
Change-Id: I5a3d5635f3c949f39d88b34a2ddab8244643f560
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2070
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some fixes to 'samd_protect' including:
- Fix a bug in which the value of 'set' parameter passed into the
function was ignored so it was impossible to remove flash
protection once it was set.
- Check the protection status of the sector via 'is_protected'
field of the corresponding 'flash_sector' structure to see if
any actual HW manipulations needs to be done.
- Change the way the errors during protection activation are
handled. Now even in the case of error in the middle of
protecting a number of sectors the subroutine would still update
the state of the sector protection in sectors array so as to
avoid cases where openocd thinks that the sector is not protected
while it actually is.
Change-Id: I4cc6445a98ec13bdd94c89f0711c17840738a215
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2027
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Bail early if trying to erase protected sector and also do not double-erase already
erased sectors.
Change-Id: Ic2d39af48c3b8e10e78d52dd978b9bc01f671c6a
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2026
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Bail early if trying to write to protected sector also mark the sector
we are writing to as dirty.
Change-Id: I892f83461792e1cc2dcccade7aa65717831a6805
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2025
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Remove 'first' and 'last' checks in 'samd_protect' since those
parameters are checked in 'handle_flash_erase_command'.
Change-Id: I30e5598a9ab656d81055f26cc63e291377605300
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2024
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This introduces a new global Tcl procedure that is run just after
init_targets and before init_boards.
Its default behaviour is to assign gdb-flash-erase-start and
gdb-flash-write-end to reasonable defaults.
The rationale for doing "reset init" before gdb erases and flashes
memory is that all flash drivers are written in assumption that they
can safely be used only after chip reset (plus chip-specific
configuration in the init handler if any). The need to use "reset
halt" after flashing is because a user expects running firmware after
loading to be the same as running it from power-on-reset.
Change-Id: I9ddc4047611904ca4ca779b73376d2739611948a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2062
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
COMMAND_PARSE_NUMBER may return, thus any memory allocated may not be
freed, simple reorder fixes the issue.
Change-Id: I0ce444a5b032f5c49b6d33a03a8c0b71cad49c8c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2065
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
GPL requires providing sources for any derived work. I do not see any
reason to not include the xscale stuff into release tarballs.
Wildcard matching is used because plain directory name matches
implicit rule for executables and xscale.c built is errorneously
attempted, and directory name with a slash duplicates a directory
(xscale/xscale) in dist.
Change-Id: Ie0266470dcb97be87a09ba2dda9b3957f7cbc2fa
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1911
Tested-by: jenkins
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GPL requires providing sources for any derived work. I do not see any
reason to not include the rlink stuff into release tarballs.
Change-Id: I686ab88994030312aca5bdfe731a72f10803b5c3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1907
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It looks like tools/ should be used only for build tools, and contrib/
is a suitable place for everything else.
Change-Id: Iddaebba0acb6d66404912ec96749b46e4be643d8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1906
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems that when xml register support was added the rtos code was not
updated to match. This then caused gdb to return the following error when
rtos support was enabled - "Remote 'g' packet reply is too long".
Change-Id: I7429c4b1efed120e2e690678d55f3d6e87ee1ff1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2054
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
nRF51 doesn't have any sort of flash page cache so we need to write
all of the data on the word-by-word basis and poll for "Flash Ready"
bit each time.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I8caffbf69ebf9a69915724704ddbe270d1bb8d92
Reviewed-on: http://openocd.zylin.com/2050
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
SoftDevice stack ihex binary, provided by Nordic expects being able to
write data necessary for its correct operation at the adresses inside UICR.
This patch exposes UICR region of flash as a second bank on the MCU to
facilitate that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: Idbc140b8de027f60655f78043877b7c054eb06f9
Reviewed-on: http://openocd.zylin.com/2013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Unfortunately due to my oversight, the original version of the
nrf51_probe function contained useless code that read the contents of
DEVICEID[0] an DEVICEID[1] registers and did nothing about it(those
registers had nothing to do with the device type information anyway).
This commit fixes that code by changing its behavior to read the HWID
field of CONFIGID register and looking up the corresponding device
information in the know devices table. This information is useful
when choosing the versions of SDK and SoftDevice for the chip
using "nRF51822 compatibility matrix".
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: Ibd80b35460df4278e86e0c2500b7dcc876eec10c
Reviewed-on: http://openocd.zylin.com/2012
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch allows users to specify TAP_TYPE from
the command line when using or1k_generic.cfg.
Change-Id: I9f4b7d8e4867658fa34bb4e92fc3a5f25227df11
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/2056
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Ignoring the value parameter in that function makes its code rather
misleading. Also the only caller of it, armv7m_restore_context already
does the whole "buf_get_u32" conversion business, so using
'value' also removes the waste of doing the conversion twice.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I515979c314d9b59ee1065c55b5bb5747c7e93f01
Reviewed-on: http://openocd.zylin.com/2057
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
output for flash page writes
The offset wasn't being considered in the "full page" write codepath, so any
writes at an offset were actually written out starting from page 0.
Change-Id: I5e70a1f35f144b3edd1ce6d9df9af9b5da6cf194
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/1965
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The JLink-OB (onboard) devices work the same way as the normal JLink
except that their PID is 0x0105 (and that's the only one we know of so
far) and their endpoint addresses are different due to there being a
CDC-ACM interface as well. These JLink-OB devices show up on a lot of
vendors' development kits as an integrated debugger.
This change simply checks whether the adapter we opened has a JLink-OB
PID and, if it does, uses the JLink-OB endpoints rather than the
default. To do this, we add a new routine, jtag_libusb_get_pid() to the
libusb adapter layer, it in turn just calls
libusb_get_device_descriptor(), which previously had no wrapper.
Also, checkpatch.pl doesn't like the VID/PID macros as defined so I
moved them to the array itself. This should have no effect on the code.
This change adds the 0102 through 0104 PIDs to openocd.rules as well as this
new 0105 PID.
Tested on an Atmel SAM4S Xplained board which has a JLink-OB, also
regression tested by using a 0x0101 PID normal JLink adapter.
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Change-Id: I121d30e57729cda3adb66e2a5dc72e1fcb7ef8b1
Reviewed-on: http://openocd.zylin.com/2031
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds support for the am43xx SoC and the AM437x GP EVM and AM438x
ePOS EVM.
Change-Id: I09cbb09072f38e0e08fdd520dedb6e67d45056be
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2047
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I5ebc924ab66c86f1902942bebc203a34d97abc64
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1899
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
instead of replicating icepick_d_tapenable in many of TI's newer
platforms, we can move to icepick.cfg and just call it from board TCL
configuration file. This is similar to the C but has a few changes we
need to make.
Change-Id: I0ab48005ccd66cd5b67b919fb5e3b462288f211d
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2030
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested on ZedBoard by Tim Sander.
Change-Id: I4316d9b4d36f01bbe91a46c78ea8bca22efb1a5a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2029
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
From testing this target does not seem to support using SYSRESETREQ, change
the default to the safe VECTRESET.
This target also has other reset issues (srst not working) that will be
addressed in another patch.
Change-Id: Icfc78347dc71aa3a062ddea63190a818d7fbc760
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1995
Tested-by: jenkins
Reviewed-by: Angus Gratton <gus@projectgus.com>
As suggested by Stian Skjelstad in a comment in:
http://openocd.zylin.com/#/c/2044/
if the USB product string cannot be read, provide a debug message so
users might get aware of a potential permission problem when looking
at the debug output.
Fix style bug found by Jenkins.
Change-Id: I6acb1c6261fec6f2bee80e4be513a5c5e29eff79
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2048
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel's SAM3 and SAM4 processor families are very close to each other
in many respects. However, so far, only the SAM4 target script
contained the magic to allow using SWD, while SAM3 was tied to JTAG
only. This e.g. prevented the CMSIS-DAP driver from accessing SAM3
devices as it only uses SWD transport (by now).
The patch pulls all the things from the SAM4 target script that are
also applicable to SAM3 devices. With the patch, an Atmel CMSIS-DAP
debugger (Atmel-ICE) was proven to be able to successfully attach to a
SAM3S-EK evaluation kit. I also cross-checked that accessing through
a SAM-ICE (Segger J-Link) still works with the patch.
Change-Id: I20dafbff8e1e9f967da950e48a56205586eeef8d
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2046
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The existing CMSIS-DAP driver matches the USB VID/PID against 0x3eb
(Atmel VID) and 0x2111 (Atmel EDBG embedded CMSIS-DAP debugger), and
then bumps the packet size from its default of 64 to 512. However, it
turned out that *all* Atmel-provided CMSIS-DAP devices (EDBG with PID
0x2111; JTAGICE3 with firmware version 3.x, PID 0x2140; new Atmel-ICE
[successor of JTAGICE3], PID 0x2141) require a 512-byte packet size.
Obviously, all run the same USB implementation inside their custom
microcontroller. Thus, it seems best to simply assume that *all*
Atmel CMSIS-DAP devices use this packet size, and don't check the PID
at all.
This has also been filed as Trac bug #68:
https://sourceforge.net/apps/trac/openocd/ticket/68
Change-Id: I942af93060fdf265fca3961841638caa6182f877
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2045
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
In the CMSIS-DAP driver, if nothing has been specified by the user, an
attempt is made to find the first device with the (mandatory)
substring "CMSIS-DAP" in any USB device's product string. However,
while (usually) all devices can be traversed, devices the user does
not have permission for cannot be read the product string from,
resulting in a NULL pointer. Trying to find the substring "CMSIS-DAP"
causes a segementation fault then.
This has also been filed as Trac bug #67:
https://sourceforge.net/apps/trac/openocd/ticket/67
Change-Id: Idfc9f072e34152e9af99fe1c8ec88c99dea4624c
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2044
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Nucleo F401 board uses STM32F401RE chip with new device id and
got more flash than existing devices (512K). This patch adds
new the identifier to probe functions so flashing will now work.
Change-Id: Ibe9c047c79244db0cfbb06610da9d84987b9f85a
Signed-off-by: Jens Hoffmann <jehoffma@gmail.com>
Reviewed-on: http://openocd.zylin.com/2037
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser
Andreas Fritiofson
Andrey Smirnov
Spencer Oliver
Franck Jullien
Tim Sander
Angus Gratton
Andrey Yurovsky
Antony Pavlov
Felipe Balbi
Oleksij Rempel
Jens Hoffmann
Jörg Wunsch