- works on Cortex-M3 with ThreadX and FreeRTOS
Compared to original patch a few nits were fixed:
- remove stricmp usage
- unsigned compare fix
- printf formatting fixes
- fixed a bug with overrunning a memory buffer allocated with malloc.
gdb connect can fail when the flash has not been probed.
During gdb connect, the flash layout is reported, but this
can not be automatically detected for a target that is
powered up and OpenOCD supports connecting to gdb server
even if the target is powered down.
The solution is to turn of the gdb_memory_map feature.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This will allow switching to using named pipes.
Split this out as a seperate commit to make changes
easier to follow.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
depending on whether the connection is over a socket
or pipe, the read is done differently.
pipes can return -1 when writing 0 bytes, make 0 byte
writes a successful no-op. 0 byte writes falls out
naturally of tcl server code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
pipes have different fd's for in/out. This makes the
code more orthogonal and prepares for adding pipes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb_memory_map cmd for example fell through and returned
ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_"
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
by ack'ing memory writes immediately and reporting either
at next memory write or stepi/continue time. GDB will then
send off a new packet that is ready by the time the previous
packet has been written to target memory.
On faster adapters this can be as much as 10% improvement.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Rather than issuing a halt and then stepi/resume, just
wait for target to halt.
Issue a sterner warning via gdb console that any gdb
register changes will be ignored in this case.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Report each region of same-size sectors separately, instead of
incorrectly reporting that every sector has the same size.
This is a longstanding bug on NOR flash chips with non-uniform
sector sizes. It was largely hidden by other bugs in flash
handling. When some of those were recently fixed, this one was
exposed as a regression on str710.
[oyvind.harboe@zylin.com: update the loop to behave on str7 ]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Put the memory map logic into its own subroutine.
This will make it a bit easier to package bugfixes,
and simplifies the query packet handling.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make most methods static; net minor object code shrink.
Likewise various data symbols; no net change.
Shrink some overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It looks like a bugfix from normal breakpoints was not
copied over.
Do not use clever mathematics and assumptions to convert from
GDB enum for break/watchpoints to OpenOCD enum.
Drop connection upon unknown breakpoint type, this code path
was not really considered by the previous code I think.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add file comments to a few files. Make the GDB server use
more conventional (pointer-free) hex digit conversion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Specifically for the port commands, clarify that the number
is optional, and omitting it causes the current number to be
displayed.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The gdb_port command can be invoked during normal execution
to report the port used for gdb, whereas it was listed as
CONFIG stage only, which caused an error when excuting
it to return the reported error.
Also in line with the grander goal of making more commands
available during all "modes" (perhaps retiring config mode),
there is no particular reason to limit gdb_port to the
config stage.
Regression was introduced in:
b3bf1d12b2 aka
v0.4.0-rc1-32-gb3bf1d1
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Most commands are usable only at runtime; so don't bother saying
that, it's noise. Moreover, tokens like EXEC are cryptic. Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are
- Configuration commands (per documentation)
- And also some commands that valid at *any* time.
Update the docs to note that "help" now shows this mode info.
This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been. This just fixes ones I noted when sanity testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use a separate variable for iterating GDB service port numbers than
the one set by the user. Restores the behavior of returning the
original port number and only incrementing the port used on success.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "flash.h"
the following form should be used.
#include <flash/flash.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "target_request.h"
the following form should be used.
#include <target/target_request.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "register.h"
the following form should be used.
#include <target/register.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "image.h"
the following form should be used.
#include <target/image.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "breakpoints.h"
the following form should be used.
#include <target/breakpoints.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "jtag.h"
the following form should be used.
#include <jtag/jtag.h>
The exception is from .c files in the same directory.
Rework gdb_init to create flexible APIs (gdb_target_add_{one,all}) and
static helper (gdb_target_start) for starting GDB services. Eliminates
duplicated code and provides general mechanisms for adding GDB services.
The 'init' command is updated to call the new API, and later patches can
decouple its policy of adding all targets therein.
Provides the new capability to use both piped and TCP servers when
multiple targets are defined. The first target fills the pipe, and
others will be started on TCP ports (unless disabled, i.e. gdb_port=0).
Several of the sites now using target_type_name() really
ought to be using an instance-specific name. Create a
function called target_name(), accessing the instance's
own (command) name.
Use it in several places that really should be displaying
instance-specific names. Also in several places which
were already doing so, but which had no wrapper to call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
There are two names that may matter on a per-target basis.
One is a per-instance name (for example, "at91sam7s.cpu").
The other is the name of its type (for example, "arm7tdmi"),
which is shared among multiple targets.
Currently target_get_name() returns the type name, which is
misleading and is rarely appropriate for target diagnostics.
Rename that as target_type_name().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Updates all command parsing of simple "enable" and "disable" arguments.
A few case in the tree use a tri-state or extended arguments, which
cannot use this simple macro.
Simlifies the xscale icache/dcache command handler logic.
No need to indirect from registered integers to pointers.
Just stash the pointers directly in the register struct,
and don't even bother registering.
This is a small code shrink, speeds register access just
a smidgeon, and gets rid of another rude exit() path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't include "target.h" from more headers than necessary. This
avoids needless interdependencies and duplicated include paths.
Don't needlessly include it in source files, either.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
By using CALL_COMMAND_HANDLER, parameters can be reordered, added, or
even removed in inherited signatures, without requiring revisiting
all of the various call sites.
Added gdb_sync feature that allows GDB to sync up to target state.
Issue "monitor gdb_sync" and the next stepi, will return immediately
with updated register values to GDB.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2754 b42882b7-edfa-0310-969c-e2dbd0fdcd60
OpenOCD doesn't actually *need* to be keeping all TCP ports
active ... creating security issues in some network configs.
Instead, let config file specify e.g. "tcl_port 0" (or gdb_port,
telnet_port) to disable that particular remote access method.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2240 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- replaces all accesses to target->type->name.
- add documentation in target_s to warn not to access field directly.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1966 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- replaces all calls to target->type->get_gdb_reg_list.
- add documentation in target_s to warn not to invoke callback directly.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1964 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Silence errors about keep_alive() not being called frequently enough unless
a gdb session is active or debugging is enabled
git-svn-id: svn://svn.berlios.de/openocd/trunk@1933 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Make startup for the various server ports be quiet, unless
debugging is active: don't emit needless scarey messages.
Update the relevant documentation and its references:
- For these port commands ... cover the default values;
convert to @deffn syntax; include their use outside of
the configuration stage; and alphabetize.
Similar updates to the rest of that small chapter:
- Highlight that there even *IS* a configuration stage, after
which some command functionality is no longer available.
- For GDB commands ... convert to @deffn syntax; alphabetize;
include a missing command (!); add missing helptext (!) for
one non-missing command; update relevant cross-references
and index entries.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1909 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- cleaned up headers to match rest of code
- added missing svn props for previously added files
git-svn-id: svn://svn.berlios.de/openocd/trunk@987 b42882b7-edfa-0310-969c-e2dbd0fdcd60
converts a number of 'simple string lookup tables' into NVP tables.
These NVP tables will be used by various commands coming in the next patch.
git-svn-id: svn://svn.berlios.de/openocd/trunk@962 b42882b7-edfa-0310-969c-e2dbd0fdcd60
from pre/post_reset event scripts. Adding the second parameter was
a mistake seen in retrospect. this gives precise control in post_reset
for *when* the post reset speed is set. The pre_reset event was
added *after* the second parameter to jtag_khz/speed
- the target implementations no longer gets involved in the reset mode
scheme. Either they reset a target into a halted mode or not.
target_process_reset()
detects if the reset halt failed or not.
- tcl target event names are now target_N_name. Mainly internal
at this early stage, but best to get the naming right now.
- added hardcoded reset modes from gdb_server.c. I don't know precisely what
these defaults should be or if it should be made configurable. Perhaps some
hardcoded defaults will do for now and it can be made configurable later.
- bugfix in cortex_m3.c for reset_run_and_xxx?
- issue syntax error upon obsolete argument in target command instead of
printing message that will surely drown in the log
git-svn-id: svn://svn.berlios.de/openocd/trunk@849 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Log output handlers now get a "const char *line"
- Added "const" to parameter.
src/helper/command.c
src/helper/command.h
- New function: 'command_output_text()'
- Log output handlers now get a "const char *line"
src/helper/options.c
- Log output handlers now get a "const char *line"
src/server/telnet_server.c
- DO not transmit NULL bytes via TELNET.
- Log output handlers now get a "const char *line"
src/server/gdb_server.c
- Log output handlers now get a "const char *line"
*** THIS INCLUDES PORTIONS OF A PATCH FROM Oyvind sent
previously to the mailing list for TCL users try
src/target/target.c
*** THIS INCLUDES PORTIONS OF A PATCH FROM Oyvind sent
previously to the mailing list for TCL users try
src/target/target.h
*** THIS INCLUDES PORTIONS OF A PATCH FROM Oyvind sent
previously to the mailing list for TCL users try
src/openocd.c
- **MAJOR** Work: New TCL/Jim function: mem2array
- **MAJOR** Work: Redirect Tcl/Jim stdio output to remote users.
- Previously: TCL output did not go to GDB.
- Previously: TCL output did not go to TELNET
- Previously: TCL output only goes to control console.
- This fixes that problem.
+ Created callbacks:
+openocd_jim_fwrite()
+openocd_jim_fread()
+openocd_jim_vfprintf()
+openocd_jim_fflush()
+openocd_jim_fgets()
src/Makefile.am
- New TCL files.
- Future note: This should be more automated. As the list of
'tcl' files grows maintaning this list will suck.
src/Jim.c
- ** THIS INCLUDES A PREVIOUS PATCH I SENT EARLIER **
- that impliments many [format] specifies JIM did not support.
- Jim_FormatString() - **MAJOR** work.
- Previously only supported "%s" "%d" and "%c"
- And what support existed had bugs.
- NEW: *MANY* formating parameters are now supported.
- TODO: The "precision" specifier is not supported.
** NEW ** This patch.
- Jim_StringToWide() test if no conversion occured.
- Jim_StringToIndex() test if no conversion occured.
- Jim_StringToDouble() test if no conversion occured.
** NEW ** This Patch. Major Work.
- Previously output from JIM did not get sent to GDB
- Ditto: Output to Telnet session.
- Above items are now fixed - By introducing callbacks
new function pointers in the "interp" structure.
- Helpers that call the callbacks.
- New function: Jim_fprintf()
- New function: Jim_vfprintf()
- New function: Jim_fwrite()
- New function: Jim_fread()
- New function: Jim_fflush()
- New function: Jim_fgets()
By default: the output is to STDIO as previous.
The "openocd.c" - redirects the output as needed.
- Jim_Panic() - Send panic to both STDERR and the interps
specified STDERR output as a 2nd choice.
- Now JIM's "stdin/stdout/stderr" paramters are "void *"
and are no longer "FILE *".
src/Jim.h
- **MAJOR**
- New JIM STDIO callbacks in the "interp" structure.
- change: "stdin/stdout/stderr" are now "void *" cookies.
- New JIM stdio helper functions.
git-svn-id: svn://svn.berlios.de/openocd/trunk@755 b42882b7-edfa-0310-969c-e2dbd0fdcd60
is post reset = reset speed.
- removed infinite loop's and exit()'s upon poor arm7/9 communication
- cleaned up error messages a bit. Push ERROR() up into fn's that
fail and can say something meaningful about what failed.
git-svn-id: svn://svn.berlios.de/openocd/trunk@511 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- hmm..... did I screw up? Was XScale and not gdb_server busted here?
My thinking was that OpenOCD has a canonical internal representation
of registers that match GDB's expectations
git-svn-id: svn://svn.berlios.de/openocd/trunk@484 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Fixed memory leak in gdb_server.c
- pushed "Error:" statements up into fn's that know something about what went wrong
- load_image now fails if target_write_memory() fails
- only issue an asynchronous halt() upon connect of GDB. Synchronous halt/reset
doesn't really work as what's required to initialize the target might involve a
special monitor sequence for the target in question
- syntax error handling improved(fewer exit()'s)
git-svn-id: svn://svn.berlios.de/openocd/trunk@482 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- switch to synchronous halt during connect. This fixes the bug
where poll() was not invoked between halt() and servicing the
'g' register packet
- halt() no longer returns error code when target is already halted, just
logs a warning. Only the halt() implementation can say anything
meaningful about why a halt() failed, so error messages are pushed
up to halt()
- fixed soft_reset_halt infinite loop bug in arm7_9_common.c. The rest
of the implementations are still busted.
- by using USER() instead of command_print() the log gets the
source + line #. Nice.
- no longer invoke exit() if soft_reset_halt fails. A reset can often
fix the problem.
git-svn-id: svn://svn.berlios.de/openocd/trunk@475 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* GDB remote server will now remain online even if the target
is in a funny state, e.g. if it requires a reset, it is
running while GDB is not in the continue or step packet,
e.g. via monitor resume/halt commands in GDB script.
* Added some _DEBUG_GDB_IO_ debug tools
* Fixed a couple of GDB server lockups, e.g. when O packets
detect a severed connection
* added ACK upon connection (send +).
* added keep-alive messages to reset so GDB protocol remains happy.
* fixed crash when timing out connection to GDB
git-svn-id: svn://svn.berlios.de/openocd/trunk@445 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- open_file_from_path() now uses logging feature
- open_file_from_path() no longer uses paths for anything but "r" mode. Fixes
bug waiting to happen.
git-svn-id: svn://svn.berlios.de/openocd/trunk@389 b42882b7-edfa-0310-969c-e2dbd0fdcd60
provides a better impeadance match for debug output char fn's, e.g. eCos.
- Line endings are now added at the caller site of command_print*(). command_print()
still adds a line ending
- echo of commands in scripts are now available via debug_level instead of
forced echo
- Added a USER_SAMELINE() for printing without a lineend.
git-svn-id: svn://svn.berlios.de/openocd/trunk@364 b42882b7-edfa-0310-969c-e2dbd0fdcd60
command and reduce confusion with "flash write_image".
- retired deprecated "flash erase" & "flash write".
- added flash_driver_protect/write/erase() that are wafer thin frontend
functions to low level driver functions. They implement checks
that were inconsistently handled by the drivers, e.g. check for
target halted was done in a spotty fashion.
- use return ERROR_COMMAND_SYNTAX_ERROR to print out
syntax of command instead of having lots of inlined replicas of
the command line syntax(some of which were wrong).
- use logging instead of dubious translation of error values to
human understandable explanations of why things failed.
The lower levels log the precise reason and the higher
levels can ammend context as the error propagates up
the call stack.
- simplified flash API slightly with logging instead of
allocating and returning information that the caller then
has to translate into print statements.
git-svn-id: svn://svn.berlios.de/openocd/trunk@337 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- add configuration option "gdb_report_data_abort <enable|disable> to enable reporting of data aborts during gdb memory read packets
- thanks to Øyvind Harboe for identifying the problem with GDB and data aborts
- fix some warnings in gdb_server.c
git-svn-id: svn://svn.berlios.de/openocd/trunk@307 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Faster DEBUG/INFO() when they are disabled
- target_read/write_buffer() now uses 16 and 32 bit access for single word aligned requests. Other requests are serviced as quickly as possible.
- *much* faster read/write GDB packets, removing timeout problems.
- GDB read/write packets w/single word aligned 32/16 bit access now use 32/16 bit word access.
- working area can now be changed on the fly. Provides a way to move working area about as MMU is enabled/disabled.
- cleaned up error messages for verify_image.
Thanks Øyvind Harboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@302 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- "monitor halt/resume" now works correctly
- "monitor sleep 10000" no longer makes the GDB protocol lock up. There is an error message and the protocol recovers nicely afterwards.
- it's now possible to connect to a target which needs a reset before halt works.
- handle failed memory access more gracefully. Connection is now closed instead of OpenOCD quitting.
- *much* improved handling of 2 second timeout on memory read packets. Especially important w/mouseover evaluation of variables in Eclipse.
- fixed memory leak upon failed memory packet reply.
- 'O' packets w/progress info is no longer sent out randomly.
- faster packet reply code.
- Thanks to Øyvind Harboe for this patch
git-svn-id: svn://svn.berlios.de/openocd/trunk@300 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- corrected blocksize handling from GDB "info mem" command
(thanks to Øyvind and Spen for these patches)
git-svn-id: svn://svn.berlios.de/openocd/trunk@278 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- gdb connection not dropped if we fail to allocate memory in query packets
git-svn-id: svn://svn.berlios.de/openocd/trunk@249 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- native win32 now handles WSAECONNRESET - no longer exits openocd
- qCRC packet now works correctly under cygwin (gdb compare-sections command)
- removed __USE_GNU define from gdbserver.c
- gdb qSupported packet is now handled, with this we are able to tell gdb packet size, memory map of target
- added new target script gdb_program_config - called before gdb flash programming
- new gdb server command gdb_memory_map (enable|disable> - default is disable
- new gdb server command gdb_flash_program (enable|disable> - default is disable
- gdb flash programming supported - vFlash packets
- image_elf_read_section now does not clear any remaining data, this was causing the gdb checksum to fail with certain files
- reformat of usbprog.c
- memory leak in command_print fixed
- updated texi doc to include new commands
- added gdb programming section to docs
git-svn-id: svn://svn.berlios.de/openocd/trunk@246 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- minor code reformat and cleanup
- updated docs to include new commands
git-svn-id: svn://svn.berlios.de/openocd/trunk@243 b42882b7-edfa-0310-969c-e2dbd0fdcd60
flash verify_image and flash erase_address.
- added patch for new parport_write_on_exit command.
Even this patch will fix some memory leaks.
(thanks too oyvind and Spen for these patches)
git-svn-id: svn://svn.berlios.de/openocd/trunk@240 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- corrected array overrun in armv7m.c
- corrected breakpoint memory allocation bug
- image read now uses fgets, vastly improves reading of large files
- improved hex file reading, support for Linear Address Record added
git-svn-id: svn://svn.berlios.de/openocd/trunk@208 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- make ep93xx and at91rm9200 bitbang JTAG interfaces dependant on ARM host (thanks to Vincent Palatin)
- various whitespace fixes
- removed various warnings
- add support for Debian GNU/kFreeBSD (thanks to Uwe Hermann)
- fix OpenOCD compilation for various platforms (thanks to Uwe Hermann and Vincent Palatin)
- switched order of JTAG chain examination and validation (examine first, then multiple validation tries even if examination failed)
- added target_request subsystem to handle requests from the target (debug messages and tracepoints implemented, future enhancements might include
semihosting, all ARM7/9 only for now)
- added support for GDB vFlashXXX packets (thanks to Pavel Chromy)
- added support for receiving data via ARM7/9 DCC
- reworked flash writing. the 'flash write' command is now deprecated and replaced by 'flash write_binary' (old syntax and behaviour) and 'flash
write_image' (write image files (bin, hex, elf, s19) to a target).
- added support for AMD/ST/SST 29F400B non-cfi flashes
git-svn-id: svn://svn.berlios.de/openocd/trunk@190 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix multiple reads from FT2232 into same buffer location (thanks to Magnus Lundin)
- retry JTAG chain validation (thanks to Magnus Lundin)
- reworked GDB packet input handling (thanks to Pavel Chromy)
- output error message when setting a watchpoint failed
- removed duplicate out-of-bounds check in at91sam7.c (thanks to Pavel Chromy)
git-svn-id: svn://svn.berlios.de/openocd/trunk@181 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed compiler warnings throughout the code (thanks to Vincent Palatin for this patch)
- added support for accessing ETB (embedded trace buffer) registers
git-svn-id: svn://svn.berlios.de/openocd/trunk@134 b42882b7-edfa-0310-969c-e2dbd0fdcd60
