The STLINK/V2 supports two api's.
This completes the support so STLINK_JTAG_API_V2 is usable.
Support for hardware srst still needs adding.
Change-Id: Ic4d0499be2a225d18abf96fd6f5ce5e295fb1f37
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/561
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The stlink api does support results for some functions - add support.
Change-Id: I39cb495408c46af8bc343b198a1e0bd4c7aee6d8
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/560
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The first available devkits for the at91sam3x8h had the ES device populated.
The ES device had an error in the CIDR, specifically in the last byte of
which the upper 3 bits identifies the chip family - cortex-m3, arm7tdmi etc.
The problem was fixed on the ES2 devices - Thanks to Pat Hickey for giving me
the heads-up.
Change-Id: I13dd7fbe0cffaf76f948188c9459dc3cf4435570
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/575
Tested-by: jenkins
Reviewed-by: Jim Norris <u17263@att.net>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The value returned from target_write_buffer is still ignored.
Change-Id: Icb49d4d1313a5e4f7df68d3f122a5f81cfa0604a
Signed-off-by: Linus Tolke <linus@tigris.org>
Reviewed-on: http://openocd.zylin.com/596
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This patch fixes the link to the Zylin ZY1000 JTAG Probe webpage.
The ZY1000 product line was acquired by Ultimate Solutions, Inc. in May 2011.
Change-Id: If68cd45a0c47aa20b2e4bb62939b2c505c8c8c2e
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/571
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The target address for the partial data needs to be bumped past the
full page data. Otherwise, the partial data overwrites the start of
the flash block.
Change-Id: I1246b2fa8acbdb8193edcf7029309f11d1c6069c
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/555
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* Added support to the FT2232 driver for the FT2232H-based
Digilent HS1 adapter.
Change-Id: Iab6cc15f299badaf115615b5d4d785ecb2273c27
Signed-off-by: Stephane Bonnet <bonnetst@hds.utc.fr>
Reviewed-on: http://openocd.zylin.com/558
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add swd_init_reset and swd_add_reset.
Add adapter_assert_reset and adapter_deassert_reset, and call them instead
of JTAG reset functions.
Change-Id: Ib2551c6fbb45513e0ae0dc331cfe3ee3f922298a
Signed-off-by: Simon Qian <simonqian.openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/526
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This functions are unfinished and work only with parameter count up to 1024.
Commands mdh and mdb from pic32mx context show values not related to memory
content if parameter count is bigger than 1024. Firt 1024 are ok.
Change-Id: Ie3f4d4a0f9d1d1a69bd3a18de2f72dd9249514cb
Signed-off-by: Salvador <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/550
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Now the the "Fast" version for memory blank check in pic32mx.c can be called:
default_flash_blank_check() instead of the "fallback" default_flash_mem_blank_check().
The command "verify_image", without working area, now don't show:
checksum mismatch - attempting binary compare
when there are no real errors in flash.
Change-Id: I256e8ae949289634e1de5c1c2861e4c4c4b7fdce
Signed-off-by: Salvador <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/549
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The stlink partially supports the cortex-m4 fp regs and requires these
defines to build.
Change-Id: Id3aa802ecc7006cb6d9f84b79ab3c21af24c1001
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/545
Tested-by: jenkins
This patch fix the register index on read/write register.
Change-Id: I7b52a927a48259d6f497ac0f474aff7ff1529e9a
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/525
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently if we have multiple transport's defined we receive an warning similar to:
must select a transport.
allow transport 'jtag'
allow transport 'swd
This removes that warning and only prints this info if transport_init fails.
Change-Id: I87126390f234bc2f705e1f150a0dcc110dcab151
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/532
Tested-by: jenkins
The bug shows up with the command "mdw addres count" and only if count>1024 (count>0x400).
The first 1024 values shows as expected, but the rest of the values are wrong.
Name of variable bytesread" is changed to "wordsread" to reflect what really does.
Change-Id: Iad79393e72da2637551c5ae6e829e3873605c520
Signed-off-by: Salvador <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/527
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add a warn message to inform the user that something is wrong
with the flash settings or command parameters.
Change-Id: Ia55868b2abf2a17845e51620b0f29b2809d841c2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/280
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch let openocd running and only close the gdb connection
on error.
Change-Id: Ifb88e16834b51207cc4c82210eab904ed8d30b71
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/523
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch fix the compare for the list size and the register index.
Change-Id: I36d5e078f57d2a9f7823cfdf0d537762e00f6929
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/516
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On operating systems with opportunistic malloc() (e.g. default setting in
GNU/Linux) malloc can sometimes allocate a huge memory region but later the
process will get killed on the first attempt to use this memory, so
checking for malloc's return value is not enough to prevent a crash.
This patch is compile-tested only.
Change-Id: I5e21663115c8e9a0ca9f3d71f7ba4bd09e5c3bb1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/521
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When gdb loads an elf file of a newer or older version of the firmware
being debugged, or when the firmware is not running yet, there's a high
probability of FreeRTOS variables to be read incorrectly, thus leading to
an attempt to allocate an enourmous amount of memory. Without this check
OpenOCD simply crashes and that's mad confusing.
Change-Id: I404a072e886d2d47d9d942cfaea8417eb8bd4a5d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/520
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The {read,write}_mem32 interface functions was asking a 32 bits buffer
but they don't need 32 bits alignment.
This will change the interface to a 8 bits buffer to remove the
alignment mismatch warning. This was causing build errors on platforms
with strict aliasing rules.
Change-Id: I338be8df5686f07a64ddb4f17c1bb494af583999
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Reviewed-on: http://openocd.zylin.com/483
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch checks the received register length with the local
configured register length and disconnect on a length missmatch.
Change-Id: I6b112c6b55a9ffb4526f582a384ffa91dc8b792f
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/517
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add floating point register read/write
functionality through the SCS debug interface.
Change-Id: Id20e109dd7cccba00671d55ca8aabeb4936cceb9
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/512
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch determine all cpu types and not only
the cortex M3 and the stm32 target use the common
target examine function from the cortex_m sources.
Change-Id: If689dd994b3855284b927fc4b206f420cf32b6c7
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/511
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch fix the slow flash write issue on pflash only devices.
The Family Reference Manual says:
For devices with FlexNVM: FlexRAM
For devices with program flash only: Programming acceleration RAM
So the acceleration RAM is available for the flash section command on
this device.
Change-Id: If6541a23a4457c5ed8858848a145f35cac63138b
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/509
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch prepend the v1 mass storage protocol to the command
buffer and simplify the usb read/write handling.
Change-Id: I709602600e93cd1eb5848fa9f4d15659ba85eb35
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/506
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This driver provides support for the P&E Micro OSBDM adapter (sometimes
named as OSJTAG), mounted on the Freescale TWRK60N512 bord. Thus, it
provides a quick start when working with this board. The driver doesn't
use BDM commands, but work with OSBDM adapter using only JTAG commands.
Change-Id: Ibc3779538e666e07651d3136431e5d44344f3b07
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-on: http://openocd.zylin.com/492
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced 7 new Cortex-M3 processors on 2012-02-28
SAM3X4C - 256KB flash
SAM3X4E - 256KB flash
SAM3X8C - 512KB flash
SAM3X8E - 512KB flash
SAM3X8H (Only on dev-kit - not in production...) - 512KB flash
SAM3A4C - 256KB flash
SAM3A8C - 256KB flash
The SAM3X/A processors still suffer from the "6 waitstates needed
to program device" errata.
The CIDR address for the SAM3X/A processors are different from the
other SAM3 processors. Unfortunately, the chip identification register
is not at a constant address across all of the SAM3 series'. As a
consequence, a simple heuristic is used to find where it's
at... If the contents at the first address is zero, then we know
that the second address is where the chip id register is.
We can deduce this because for those SAM's that have the chip id @ 0x400e0940,
the first address, 0x400e0740, is located in the memory map of the Power
Management Controller (PMC). Furthermore, the address is not used by the PMC.
So when read, the memory controller returns zero.
Another interesting change is the flash bank address for flash bank 1.
It is not fixed at 0x00100000 like the Sam3U. Bank 1 of the at91sam3a/x
series starts at 0x00080000 + half the total flash size. Thus for the 256KB
devices Bank 1 is located at 0x000A0000, and for the 512KB devices Bank 1 is
located at 0x000C0000.
The configuration files for the SAM3X/A processors will follow
Change-Id: I6c3a707c00e05d993a2ad1d5a423f23b37ffd553
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/505
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
arm7_9_prepare_reset_halt is long since gone and the functionality
is implemented in the target's assert_reset handler.
Change-Id: Ib03c730cb39d68e5e3bb42f92af13daf8074e4e2
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/515
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.
Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
target_call_event_callbacks needs to be called after debug entry otherwise
we will get a console pc mismatch.
Change-Id: I278137736d5e85ca9662c306f6ac81336d8eb6cf
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/499
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The SUPC (Supply Controller) registers are on different base addresses on different
SAM3 chips:
SAM3U: 0x400e1210
SAM3N: 0x400e1410
SAM3S: 0x400e1410
This creates a problem with the sam3_reg_list array which is const, but would need
to be changed at runtime to account for this variability. As this register is not
used anywhere, it's simplest to just remove it.
Change-Id: I987eb371648d826aa6d5e9de18d38c7bb66d6fca
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/495
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Lock region count and sector sizes did not match datasheet.
(see 6500C-ATARM-8FE11 "SAM3S Series Datasheet", Table 7-1)
Change-Id: Ic511802f96ed03856467a24a6736349205a0576a
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/493
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
implement stlink_usb_send and use it to fix stlink_usb_write_mem
using two calls to stlink_usb_recv is inappropriate since each
call issues a SG command on stlink-v1, resulting in errors
Change-Id: I24ef9f2dda284e041dc4a532b59968a77eebe702
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/498
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch moves the bulk of the stlink read/write code into the
stlink_usb_xfer set of functions and implements stlink_usb_recv
in terms of the generic stlink_usb_xfer
stlink_usb_xfer will be needed to implement stlink_usb_send
without code duplication
stlink_usb_xfer:
-sends the stlink command
-performs a read or write (as requested)
-checks the status (v1 only)
Change-Id: I0137d52620bd4883d46c9977a9e73f67622000a1
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/477
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The assert introduced in 00c8648351 checks
whether the programming offset equals to page_size of the flash, while it
wants to check whether the offset is a multiple of the page_size.
Change-Id: I794d021951a28c1cc520b5eea5d500f097721b06
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/482
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Currently stm32lx flash driver will remove the readout protection if set
during a probe.
This may not be what the user wants, so let them decide.
Change-Id: I8575e3b339b10a4f7bac57cca9586dcab513d347
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/465
Tested-by: jenkins
implement stlink_usb_send and use it to fix stlink_usb_write_mem
using two calls to stlink_usb_recv is inappropriate since each
call issues a SG command on stlink-v1, resulting in errors
Change-Id: I52ff9ee8f5d9ae0d47356477468eb98952205c99
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/478
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
when -ignore-version is used we should mask of the upper 4bits not 8bits.
Change-Id: I9ffe24c2aeeb414677357a647609fdf018890194
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/473
Tested-by: jenkins
This fixes scan_chain to correctly print all the expected_ids.
Change-Id: I93738980d85e0fe369d40c58b19339424d37ec34
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/474
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This enable the stm32f2x flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 1048576 bytes from file stm32f4x.bin in 30.453804s (33.625 KiB/s)
after - wrote 1048576 bytes from file stm32f4x.bin in 23.679497s (43.244 KiB/s)
This also fixes a bug that was in the old flash loader.
The old loader waited while bit16 of the status reg was 0, the new
loader waits until this bit is 0 as stated in the flash spec.
Bizarrely this bug did not effect programming on any tested parts.
Change-Id: I3efc94d42cbe81283673a8f4203700638080af6e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/460
Tested-by: jenkins
This enable the Stellaris flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 65536 bytes from file test.bin in 5.486040s (11.666 KiB/s)
after - wrote 65536 bytes from file test.bin in 2.274001s (28.144 KiB/s)
Change-Id: I9004c9aadffa1ae3b0cbf908e6549b5b1f794508
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/403
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Currently the stm32f1x flash driver uses an asynchronous algorithm
as part of the block flash programming. This greatly speeds up flash
programming as the target is always running.
Moving the async code to the target enable other targets to use this
added functionality.
Change-Id: I8e53f094c2ef7848a7f86ddb9a35b6edbfc8454a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/402
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is a much cleaner solution to the problem of allocating as much
working area as possible than what is currently being done in most/all flash
drivers (which is: try an arbitrary sized chunk, if it fails, pick a smaller
number, rinse and repeat).
Use this function to find out how much working area is available, limit or
restrict that amount at will and then simply allocate it.
Change-Id: Ib7d5d0b7485aed3e0a4fad60c1bedb7dfd16146f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/446
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The existing allocator couldn't reuse a freed allocation if the sizes
didn't match exactly. That led to problems when for example a flash write
routine had allocated all of the working area to speed up operation. A
subsequent verify pass couldn't allocate space for the checksum algorithm
even though all previous allocations had been freed.
This allocator is marginally more complex, but solves the above problem by
splitting larger free areas to fulfill smaller requests and by merging
released areas into adjacent free areas.
An initial free area, covering the entire specified address range, is set
up on first allocation, and all allocations are split off from (and
ultimately merged into) that one. It can also easily be adapted to support
several disjoint working areas for the same target, by setting up several
initial free areas and slightly modifying the merge code.
Change-Id: I6faaf9801312bb19a4fa4474694a0cd1c6e0ab54
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/445
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This brings the stlink driver inline with the rest of OpenOCD.
If the user configures the tap as -expected-id 0 then the IDCODE will be
treated as a wildcard and ignored.
Change-Id: I99160c69b2b40f5b1f608bb59ab6630894502fd8
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/476
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
This patch add the status check.
Change-Id: I0fdb9bf66dad5ae416c7aa4c6e19116f846571f9
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/463
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
automake 1.11.2 throws `pkglibdir' is not a legitimate directory for `DATA'
if nobase_dist_pkglib_DATA is used.
We work around this issue by defining our own location.
Change-Id: I3c29e2df0b67e745283c50d358e31699bd60dc74
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/457
Tested-by: jenkins
I used the CPUID instead of adding a new argument to the flash bank command
Fixed Type in comments
Add the failsafe return value in device_id
Change-Id: Ieb5a46fc002b5390a0c81bc8b49f6c687036ae1d
Signed-off-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-on: http://openocd.zylin.com/438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add the bootloader define.
Change-Id: I280a8a35c3514910dd381de3ab8ad59c9bd74ca1
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/455
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ref manuals for the stm32f2x (RM0033 Rev4) and stm32f4x (RM0090 rev1)
are unclear to the address of the flash size register (F_ID).
According to contacts @ ST this is the correct address, the manuals will be
updated in due coarse.
Change-Id: If9fb83b3100458d17038cf27c2b23355e1dc5a9e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/448
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
This adds init_board procedure that behaves exactly the same as
init_targets - it can be overriden by "next level" scripts. This
procedure is executed after init_targets, allowing common stuff (jtag
chain, memory, flash, ...) to be configured in target script (via
init_target) and leaving rest (like additional memory, reset
configuration, reset-init handlers, ...) to be done in init_board.
This makes init_targets scheme more complete and easier to use - current
board scripts will not need new init_targets, because everything can be
"packed" in init_boards. Moreover it solves the problem of variables
being set in init_targets (executed after init), which were not
accessible by "linear" scripts (parsed before init). All that has to be
done is to enclose all code in board config file in init_board
procedure.
Change-Id: I0736b1ff9873a687966407d62b58ccf29a8e597b
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/427
Reviewed-by: Chris Morgan <chmorgan@gmail.com>
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This issue was caused by uncrustify not correctly converting the doxygen
comments.
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Change-Id: Ie6dc3b057a08603b670cb27312e5f0d989426e6c
Reviewed-on: http://openocd.zylin.com/431
Tested-by: jenkins
This patch add a validation for the supported jtag api version.
Change-Id: I0b51350e58e351d6662f4039c0a9e9d0d79ba4ec
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/405
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Correct the offset to the read pointer when clearing it on error.
Also restrict the instruction set to armv6-m so the flash driver can be
used on Cortex-M0 parts with the same flash controller.
Change-Id: I380f9dabcc41fb6e4d43a7e02f355e2381913f39
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/399
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Replace the big stack-allocated buffer with a much bigger heap-allocated.
There was no explanation for the apparently arbitrary chunk size, and
performance was improved by increasing it, leveling out at about 4k.
Change-Id: I3b06d4469092ec8d89d0ce05bff0b7cf213c5062
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/404
Tested-by: jenkins
Reviewed-by: Marti Bolivar <mbolivar@leaflabs.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This patch test the device version and differentiate between
v1 and v2 devices.
Change-Id: Ie79bf2c5534211493b004329fb6d5b9d4ea5453b
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/396
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add jtag support to the stlink driver add
two new transport types, JTAG and SWIM.
Change-Id: I7089d74250330be5c6a01c24066307641df7d11e
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/393
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
for some reason the following commit was incorrect
769064de4b
Only the Sandstorm and Fury class should write this register.
Change-Id: Ie18f1da6e9b59fb99cca47aa93c7f2fee447ccea
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/400
Tested-by: jenkins
For example, when blocks 2 and 3 were erased, openocd reported "erased blocks 2 to 4". That should be "2 to 3", I think.
Change-Id: Icece63dedd3dd931b70fa73616819a19572e39de
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/385
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
SPAS register (OOB size) is left wrong after reset with respect to 2KiB page NAND chip. That will lead to ECC errors after 'reset halt'.
Change-Id: If5a4685cb8d6be35879453951611ef1059da219c
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/384
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch is based on Erik Ahlén's work on i.MX35 NFC support. Basically it redefines the CCM.RCSR register which is in a different address in i.MX25.
Change-Id: Ia6faf9cb5efae5e564b72ef9a9b7c7f8bfde3ce0
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/383
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
stellaris_set_flash_timing should only be used for Sandstorm and Fury
device classes.
Change-Id: Ib5eff9d954c039f2c5726a8ecc3ee45d1694cfd3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/389
Tested-by: jenkins
read the target class during probe and save for later use.
Change-Id: Ib3ad20edc7d206b7f434bdcc6b947e6a5f06dd1f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/388
Tested-by: jenkins
This makes the stlink target use the std armv7m_arch_state giving
consistent OpenOCD output.
Added debug entry handler so we get debug entry reason.
Change-Id: Ia3c1380fd5033a8e541b0d45a7c3559f1b05957d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/379
Tested-by: jenkins
