STM32WB1x devices has a single flash bank up to 320 KB (page 2KB)
note: STM32WB5x/WB3x are single banks as well but do have 4KB as page size.
note: remove the assert that checks if max_mages is power of two, because
STM32WB1x flash size is not a power of 2
Change-Id: Ib514cf989ecb819d25d1c4a65d641d0a1a3d9f18
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6129
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this device has single bank flash architecture up to 64KB (page 2KB)
reference: RM0444 rev 5
Change-Id: Ia213c01accb950fcbb7519e08057dae11b4443dd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6128
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
switching to C loader instead of the assembly version will enhance readability
will reduce the maintenance effort.
besides the switch to C loader, we added a new parameters to the loader
like flash_word_size and flash_sr_bsy_mask in order to support properly
STM32U5x and STM32G0Bx/G0Cx in dual-bank mode.
Change-Id: I24cafc2ba637a065593a0506eae787b21080a0ba
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6109
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
If the remaining memory for the buffer is less than 256 bytes,
the memory allocated for the write algorithm in the target is not freed.
Fixes: ba131f30a0 (Flash driver for STM32G0xx and STM32G4xx)
Change-Id: Ic649f6c39799d76725b0c69ff3a009a3f510e17f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6486
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
according the RM0453, the second core have a different Flash CR and SR
registers for flash operations (called C2CR and C2SR).
so we need to a different flash_regs than older L4 devices.
@see stm32wl_cpu2_flash_regs
the C2CR register don't contain LOCK and OPTLOCK bits, and this explain
the addition of new register index called STM32_FLASH_CR_WLK_INDEX to
look-up the CR with lock, to be used in locking/unlocking the flash.
note: DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
to solve this read the UID64 (IEEE 64-bit unique device ID register)
Change-Id: Ifb6e291bf97f814f0b9987b2c40f3037959f7af4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6050
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this device has a dual bank flash architecture up to 512 KB (page 2KB)
reference: RM0444 Rev 5
notes:
- 128k variant is always single bank
- 256k variant flash is contiguous (no gap) in dual bank mode
- BKER is bit 13 vs bit 11 for other devices
> added cr_bker_mask in stm32l4_flash_bank struct
- BSY2 for bank 2 operations
> added sr_bsy_mask in stm32l4_flash_bank struct
> proposed optimization: always wait for (BSY1 | BSY2) with
STM32G0Bx/G0Cx devices only (for L4+ devices BSY2=PEMPTY)
TODO: update flashloader to use the proper BSY bits
temporarily don't use the loader in dual bank mode
Change-Id: I54b0c93b494e7209da818791d15edd8cd42c2732
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6036
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
This struct element is replaced by the usage of F_HAS_L5_FLASH_REGS flag:
since over this driver stm32l4_flash_regs is the default register layout,
and the only exception is STM32L5 family,
so it's simpler to manage it using a flag.
Note: the same flag will be used with STM32U5 devices, as they have
the same registers layout, which explains the move of stm32l5_s_flash_regs
before the switch(device_id) in order to not re-write this for STM32U5.
Change-Id: I3b67a6f558d9350f609a22524012b6fceb7de7c2
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6435
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this capability permits to program the flash if we cannot reserve a workarea.
the introduction the command 'stm32l4x flashloader <bank_id> [enable|disable]'
helps to automatically skip using the flashloader if needed.
Change-Id: Id29213c85ee5c7c487cfee21554f5a7ea50db6c9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6273
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
when RDP level is 0.5 the provided work-area should reside in non-secure RAM
to ensure that:
- add a hint in the driver level
- reduce the usage of secure RAM only when TZEN=1 and RDP is not 0.5
(check the target configuration file)
Change-Id: Idbf2325e609b84ef8480eefdb49a176fdf7e07c7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6035
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STM32L5 flash memory is aliased to 0x0C000000, this address mapping
is used for secure applications. (0x08000000 for non-secure)
this change allows the programming of secure and non-secure flash
when trustzone is enabled and RDP level is 0
Change-Id: I89d1f1b5d493cf01a142ca4dbfef5a3731cab96e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
auto re-probing is ensured by having optr cache set in the
last probe operation.
this will help to detect if flash options have been modified by the
running application or by the user using direct register access.
Change-Id: I05cd7ab9e83a7fc26ac6cff175b3c11b0efa2eb5
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5935
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this command will help to enable/disable or display the TrustZone security,
using the TZEN option bit.
Note: This command works only with devices with TrustZone, eg. STM32L5.
Note: This command will perform an OBL_Launch after modifying the TZEN.
Change-Id: I4aef15bf57d09c1658d37858143d23b1d43de1f0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5542
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
in line 1391, get_stm32l4_bank_type_str(bank) will always output the same
value "Flash single" since the variable stm32l4_info->dual_bank_mode is false
by default, stm32l4_info->dual_bank_mode will be set correctly afterward
in the switch case at line 1467
thus the need to remove the usage of get_stm32l4_bank_type_str(bank) before
stm32l4_info->dual_bank_mode initialization.
Fixes: 64c2e03b23 ("flash/nor: improved API of flash_driver.info & fixed buffer overruns")
Change-Id: Ia8dc7e144e0ded6143682eb514c247f27859ff81
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6411
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: I7e113b06b74f2d8d9cc4c0ce1957994a1c49c964
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6419
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Remove useless setting of the 'is_erased' flag after a flash
modification. Also, remove code that erroneously depends on
this flag.
Keep the flag for now since it is still used by the
erase_check() functionality.
See commit 07da3b3913
Change-Id: Ia046905bc9e0cb2572145f19251c3e10c4e2d553
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6279
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new helper to make the code more readable.
Change-Id: I11b2a79dbc6f93f6cfde382bcc00dd7ff710d908
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6375
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
There are ~900 Yoda conditions to be aligned to the coding style.
For recurrent Yoda conditions it's preferable using a trivial
script in order to minimize the review effort.
E.g. comparison of uppercase macro/enum with lowercase variable:
- ...(ERROR_OK == retval)...
+ ...(retval == ERROR_OK)...
Patch generated automatically with the command:
sed -i \
's/(\([A-Z][A-Z0-9_]*\) \([=!]=\) \([a-z][a-z0-9_]*\))/(\3 \2 \1)/g' \
$(find src/ -type f)
While there, remove the braces {} around a single statement block
to prevent warning from checkpatch.
Change-Id: If585b0a4b4578879c87b2dd74d9e0025e275ec6b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6354
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
The current implementation fails due to the assert() statements in
get_stm32l4_rev_str() and get_stm32l4_bank_type_str(). Rearrange the
code in order to fix the problem.
Change-Id: If19c648dec8ddd3ef2fb801150114104b34c3bf2
Signed-off-by: Marc Schink <dev@zapb.de>
Fixes: 64c2e03b23 ("flash/nor: improved API of flash_driver.info & fixed buffer overruns")
Reviewed-on: http://openocd.zylin.com/6326
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
1) The API of "info" callback in "struct flash_driver" has been
improved. Fixed buffers for strings
2) Removed the calls to snprintf() from the flash_driver.info
implementations. Many of them were used in an unsafe manner
(buffer overruns were possible).
Change-Id: I42ab8a8018d01f9af43c5ba49f650c3cb5d31dcb
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6182
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is not a bug fix, this for loop will issue only one match
adding the break will save unnecessary more loops.
Change-Id: Ic1484ea8cdea1b284eb570f9e3e7818e07daf5cd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6248
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
introduction of 'enum stm32l4_rdp' enumerating possible RDP levels for
devices with and without TrustZone.
also in 'stm32l4_flash_bank' structure we added and rdp and tzen members
to store read values by the helper 'stm32l4_sync_rdp_tzen'
these new members are used to display security and protection status
while probing the flash.
Change-Id: Icf883189715278a3323fe210d295047678b16592
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5541
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
instead of adding a new member into stm32l4_part_info for every relevant
feature, .flags serves as container for the devices' features.
identified features: F_HAS_DUAL_BANK, F_USE_ALL_WRPXX, F_HAS_TZ
Change-Id: I3093e54c6509dec33043ebe6f87675198bf1967a
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is specially needed when, in the probe routine, device is not
found among the stm32l4_parts. In this case, the stm32l4_flash_bank->part_info
is undefined and inadvertentanly used afterwards:
part_info = stm32l4_info->part_info;
If the stm32l4_flash_bank is zero init, the probe routine checks for
the validity of the part_info field in the previous struct and correctly
detects the unsupported (or not found) condition, raising an error
rather than a SIGSEGV
Change-Id: I7d9d669fb3fa7f8f0903acd60046966b4acb0031
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6103
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
flash_regs table is introduced within stm32l4_flash_bank struct in order
to get correct register offsets, by using the driver internal function
'stm32l4_get_flash_reg_by_index'.
To use efficiently register indexes, stm32l4 _[get|read|write]_flash_reg
functions are surcharged to accept register indexes.
IMPORTANT: stm32l4_write_option is not surcharged, and they always accept
the option register offset.
tested on NUCLEO-G474RE and STM32L4R9I-DISCO
Change-Id: I739d3e97d63b831af6aa569c5629db0000209551
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5509
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Modify the format strings to properly handle uint32_t data types.
Change the type of variable retval in 'nor/ambiqmicro.c' to match
both the value to carry and the returned type of the function.
Fix the prototype mismatch of function lpc2900_address2sector()
between the header and the C file.
Change-Id: I68ffba9bd83eec8132f83bff3af993861fd09d84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5816
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
There are cases where the pointer is set to NULL after free(), but
then re-assigned within few lines. Drop the setting to NULL when
this is evident. Anyway, the compiler will remove the useless
assignment so no reason to be too much aggressive in this change.
Change-Id: I55b2ce7cbe201410016398933e34d33a4b66e30b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5811
Tested-by: jenkins
Fix typos and duplicated words in comments and strings.
Change-Id: I64282c7018462deefeeb8e5f4d0d81942425b3fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5758
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
Use 'unsigned int' and 'bool' instead of 'int' where appropriate.
While at it, fix some coding style issues.
No new Clang analyzer warnings.
Change-Id: I700802c9ee81c3c7ae73108f0f8f06b15a4345f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4929
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The current version erroneously allows any number of arguments >= 1.
Change-Id: I64156c11b48d411c72bebbf866954818cd036ff2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5716
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
a table with register offset will be introduced, thus correct register
addresses will be obtained using this table and the driver internal
function 'stm32l4_get_flash_reg' will be responsible of this.
Change-Id: I74bf61a83fe53575623640af0328b3253ecc796f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5508
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Michael Jung <mijung@gmx.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to RM0432 rev. 6, only 0x1001 "Z" rev. applies for STM32L4P5/Q5.
Verified on real device. Whether other revisions exist is unclear.
Change-Id: I761ae077d089b06925fc0fe1ff2b1e478b8a66fa
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5521
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix build error on Mac OS X Catalina (10.15.4) caused by formatting
stm32l4_info->wrpxxr_mask, which is uint32_t, as uint16_t in the debug
log message. Adding casting to uint16_t before substitution because only
lower 16 bits are significant for debug purposes.
Change-Id: Iddb87cd156dfc84ab1f91cd15a1ddee6b646d412
Signed-off-by: Ilya Kharin <akscram@gmail.com>
Reviewed-on: http://openocd.zylin.com/5590
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32WB3x devices' flash are quite similar to STM32WB5x,
except the maximum flash size, which is 512K for WB3x and 1M for WB5x
Change-Id: I3098d7153a7429e0e72c75cec962c05768b0b018
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5475
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32WLEx devices are based on arm Cortex-M4 running at 48MHz,
contains a single bank of maximum 256 Kbytes of flash memory.
there is 3 variants with different Flash/RAM sizes:
STM32WLE5JC : 256K/64K
STM32WLE5JB : 128K/48K
STM32WLE5J8 : 64K/20K
the work-area size is set to 20 kb to fit in STM32WLE5J8
Change-Id: Ie8e186fe4be97cbc25c53ef0ade4b4dbbcee6f66
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5450
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash module of STM32G0/G4 family is quite similar to the one of
STM32L4, so only minor changes are required, in particular
adaption of flash loader to Cortex-M0. Register addresses
passed to flash loader to simplify integration of L5.
Added re-probe after option byte load.
Added flash size override via cfg file.
WRPxxR mask now based on max. number of pages instead of fixed 0xFF,
as G4 devices fill up unused bits with '1'.
Sizes in stm32l4_probe changed to multiples of 1kB.
Tested with Nucleo-G071RB, G030J6, Nucleo-G431RB and Nucleo-G474RE.
Gap handling in G4 Cat. 3 dual bank mode tested with STM32G473RB.
This handling isn't optimal as the bank size includes the
size of the gap. WB not tested.
Change-Id: I24df7c065afeb71c11c7e96de4aa9fdb91845593
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4807
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Also add locking after option write, it was missing at all.
Change-Id: I0227c6a74866f0fe8e40aa58616f0b3115ad5af0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5361
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Fix comment of tested errors in asm src.
List all relevant errors in FLASH_ERROR mask: FLASH_PROGERR was missing
and any trial to re-program already programmed double word ended up
in the error bit held uncleared and flash write permanetly repeating
the error message until reset.
Lock the bank also after unsuccesfull write_block run.
Set async target algo block size to size of double word.
Remove warning in case of write_block success. In case of error
use LOG_ERROR instead of warning.
Change-Id: Ibf6d5e306a4c2eaa43de67d636b4902c737f02f3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5360
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The original code paded the write chunk with random bytes by overrunning
the buffer. An user can easily regard the random bytes to
be a programming error.
Change-Id: Ib0f47b5bc406bc6a7c32f3d929bf324a17c7c1e1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5359
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
STM32L4P/Q devices have:
- similar flash layout as STM32L4R/S devices
- 1024K of flash memory (some parts have 512K only)
tested on NUCLEO-L4P5ZG using board/st_nucleo_l4.cfg
Change-Id: I77047351bc7dcd7c76d0f31a77be73005104a06f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5392
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>