It can be sped up later, once it's known the PLLs are active.
Note that modern tools from TI all use adaptive clocking; and
that if that's done with OpenOCD, "too fast" is also a non-issue.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2740 b42882b7-edfa-0310-969c-e2dbd0fdcd60
garbage after the expected data (from the TAPs' BYPASS or IDCODE
registers).
NOTE that there was previously some code that looked like it was
trying to do this ... which didn't work, because it was looping
over the list of expected TAPs, and never checked *after* that
list completed! That could hide some *nasty* reset issues...
Also replace a now-obsolete scanchain length test with one that
behaves correctly; and update reporting of unexpected IDCODEs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2739 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch modifies an error message which, in its original state,
I find somewhat unhelpful. So a small hint was added.
Signed-off-by: Johnny Halfmoon <jhalfmoon at milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2738 b42882b7-edfa-0310-969c-e2dbd0fdcd60
done on exit from the config stage, how JTAG clocking issues can
trigger errors there, and how to avoid such problems.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2737 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Shrink messaging during resets, primarily by getting rid of
"nothing happened" noise that hides *useful* information.
- Improve: the "no IDCODE" message by identifying which tap only
supports BYPASS; and the TAP event strings.
Related minor code updates:
- Remove two needless tests when examining the chain: we know
we have a TAP, and that all TAPs have names.
- Clean up two loops, turning "while"s into "for"s which better
show what's actually being done.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2736 b42882b7-edfa-0310-969c-e2dbd0fdcd60
for disabling TAPs. We don't actually know how to make any
JRCs which do that yet; but when we do, this will matter.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2735 b42882b7-edfa-0310-969c-e2dbd0fdcd60
and Tcl/external):
- Reorder so *both* paths (TCK/TMS or TRST) can enable TAPs with
ICEpick ... first C code flags TAPs that got disabled, then call
any Tcl code that might want to re-enable them.
- Always call the C/internal handlers when JTAG operations can be
issued; previously that wasn't done when TRST was used.
Plus some small cleanups (whitespace, strings, better messaging
during debug and on some errors) to reset-related code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2730 b42882b7-edfa-0310-969c-e2dbd0fdcd60
avoid a duplicate test.
Plus other cleanup in the same code: be "static", sane line lengths
for source and diagnostics, and fix misleading variable names.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2725 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Erase logic:
- command invocation
+ treat "nand erase N" (no offset/length) as "erase whole chip N"
+ catch a few more bogus parameter cases, like length == 0 (sigh)
- nand_erase() should be static
- on error
+ say which block failed, and if it was a bad block
+ don't give up after the first error; try to erase the rest
- on success, say which nand device was erased (name isn't unique)
Device list ("nand list"):
- say how many blocks there are
- split summary into two lines
- give example in the docs
Doc tweaks:
- Use @option{...} for DaVinci's supported hardware ECC options
For the record, I've observed that _sometimes_ erasing bad blocks causes
failure reports, and that manufacturer bad block markers aren't always
erasable (even when erasing their blocks doesn't trigger an error report).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2724 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- update comments to say so.
- update docs to clarify that the "arm9tdmi" command prefix
is a misnomer.
- bugfix some messages that wrongly assume only ARM9TDMI
based processors use this code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2719 b42882b7-edfa-0310-969c-e2dbd0fdcd60
JTAG clocking by gating the core clock, and workarounds.
Most details are with the "halt" command, which is one
of the first places this issue will be noticed.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2718 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update the board config for the DaVinci DM355 EVM so the reset-init
event handler does the rest of the work it should do:
- minor PLL setup bugfixes
- initialize the DDR2 controller
- probe both NAND banks
- initialize UART0
- enable the icache
git-svn-id: svn://svn.berlios.de/openocd/trunk@2699 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Cleanup some the downloaded ARM target algorithm code:
- Provide more complete disassembly of the DCC bulk write code
- Make code blocks "static const", in case GCC doesn't
- Fix some tabbing/layout issues
- Make some arm7_9_common.h flags be "bool" not "int"; and compact
the layout a bit (group most bools together)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2698 b42882b7-edfa-0310-969c-e2dbd0fdcd60
