Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Otherwise the new alignment checking algorithm thinks that the
address is not aligned, because it is way beyond the last sector.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.
Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.
We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip. This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Much to my surprise, I observed a "flash erase_address ..."
command erasing data which I said should not be erased.
The issue turns out to be generic NOR flash code which was
silently, and rather dangerously, morphing partial-sector
references into unrequested whole-sector ones.
This patch removes that low-level morphing. If desired, it
can and should be done in higher level code. (We might need
to fix some stuff in the GDB server code.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's currently allocating a big buffer but writing it out in
units of sizeof(host's pointer) ... sub-optimal.
Plus fix a couple minor coding style goofs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Word count == size/4; cope. And increase buf_min so it's large
enough to cover the overhead in my tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Try to right-size the SRAM buffers, by not:
- using them for very small writes
- giving up when a large buffer isn't available
- allocating buffers much larger than their data
Also don't:
- bother loading the code unless we allocate the writebuffer too
- be so verbose with messaging:
* be more concise
* reduce importance (e.g. DEBUG not WARNING)
* remove duplication
The minimum buffer size is something of a guess. It's eight
times smaller than before, almost the same size as the code
being downloaded. It probably deserves some tuning.
Also, note an erratum affecting flash protection on some chips;
and narrow many over-wide lines affected by the above changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Refactored the write page raw function into two new functions
for writing data to a NAND device and then another function to
finish up a write to a NAND device. This includes some new
updates to introduce more error checking to existing code.
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Added a new function to encapsulate reading a page of data from
a NAND device using either the read_block_data function of a NAND
controller or to use direct reading of data from the NAND device.
This also adds some performance enhancements and uses the read_data
function if the read_block_data function fails safely (because it
can't allocate a buffer in the working area).
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Someday revisit various issues: Tempest parts support writing
more than one word at a time; for some target firmware it might
be necessary to save and restore flash IRQ configuration. (The
safest policy is likely to always reset after flash updates.)
Plus swap some undesirable TAB characters with SPACE.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix potential memory leak: make sure the per-bank data
structures are only allocated in probe(), and that calling
probe() multiple times is a NOP. Use it for auto_probe().
Require probe() to have done its thing: don't make access
routines cope with it not having been called. Shrink a
bunch of failure paths; and in some cases, correct them.
Don't needlessly insist on a halted target for probe().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
No point in reading and discarding a status value when fetching
part description data. Or having that needless "#if 0" code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Previously "reading" clock info (and part info) also, as a side
effect, wrote the flash timing register. Instead, be more safe:
"reading" should only read. Write paths still refresh timing,
coping with changes the application code may have made.
Also rename the routine which sets flash timing, indicating what
it's really doing; it's got nothing to do with a "mode".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I added the remaining devices and device IDs to stellaris.c, and
removed several devices that don't exist on the Stellaris web page.
Additionally, I found a few devices with duplicate IDs ... the DID1
Version Number for LM3Sxxx parts have DID1 Version = 0x0, and for
LM3Sxxxx have DID1 Version = 0x1. So I extended the comparison to
use the VER and FAM fields from DID1 also.
ID=0x33: LM3S812 (DID1v0) and LM3S2616 (DID1v1)
ID=0x39: LM3S808 (DID1v0) and LM3S2276 (DID1v1)
These are the parts I removed from the file for lack of documentation
(no data sheet to confirm part ID):
LM3S318,
LM3S1101, LM3S1108,
LM3S1615, LM3S1616,
LM3S2016,
LM3S2101, LM3S2108,
LM3S3759, LM3S3768,
LM3S5757, LM3S5767, LM3S5768, LM3S5769,
LM3S6815, LM3S6816,
LM3S6915, LM3S6916,
LM3S6111, LM3S6118.
Also, sort devices according to part number.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Bugfix the read side of flash protection:
- read the right register(s)!
- handle more than 64K
- record the results in the right places
- don't display garbage.
Partially bugfix the write side:
- use 2KB lock regions instead of 1KB pages (!)
- validate input range
- don't try to _remove_ protection (it's write-once)
- #define values we'll need to commit writes.
- ... still doesn't handle pages over 64KB mark, or commit writes
And minor cleanup and fixes:
- get rid of some forward decls
- properly locate a doxygen comment
- fix some bad indentation
- remove superfluous #include
- add a new part ID (many are still missing)
- make the downloaded algorithm code be read-only
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move most declarations in <target/armv4_5.h> to <target/arm.h>
and update users.
What's left in the older file is stuff that I think should be
removed ... the old register cache access stuff, which makes it
awkward to support microcontroller profile (Cortex-M) cores.
The armv4_5_run_algorithm() declaration was moved too, even
though it's not yet as generic as it probably ought to be.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move the ARM opcode macros from <target/armv4_5.h>, and a few
Thumb2 ones from <target/armv7m.h>, to more appropriate homes
in a new <target/arm_opcodes.h> file.
Removed duplicate opcodes from that v7m/Thumb2 set. Protected
a few macro argument references by adding missing parentheses.
Tightening up some of the line lengths turned up a curious artifact:
the macros for the Thumb opcodes are all 32 bits wide, not 16 bits.
There's currently no explanation for why it's done that way...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename the existing 'flash banks' implementation as 'flash list', and
replace the broken 'flash_banks' TCL wrapper with a new command handler.
Adds documentation for the new 'flash list' command in the user guide.
The 'flash banks' command produces a list that needs to be formatted
properly for GDB's 'mem info' to work properly. The flash_banks TCL
wrapper provided this formatting, but wrappers no longer work for
second-level commands as they did in the past. With this patch,
the 'flash_banks' command can be used with the new command syntax
and display the required information.
More updates from the code review by Steve Grubb <sgrubb@redhat.com>.
The Jim float-comparision bug just gets a comment not a fix, though.
Cc: Steve Grubb <sgrubb@redhat.com>.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename nand.h as flash/nand/core.h, chase consumers. The public APIs
need to be sorted out with imp.h, but this allows other changes to
begin improving the separation between policy and mechanism.
Moves #include <target/target.h> and #include "driver.h" into the
internal headers or source files, removing it from <flash/nand/core.h>.
Moves commands into nand/tcl.c and core implementation to 'nand/core.c'
and 'nand/fileio.c'. Eliminates 'flash/nand.c'.
Adds 'nand/imp.h' to share routines between TCL commands and core.
This work parallels the NOR directory, encapsulating the NAND drivers
into a separate file. This takes an extra step by encapsulating the
type of data structure used to manage the drivers, allowing it to be
changed from an array to a dynamic list in the future.
Move the bulk of the flash.h file into flash/nor/core.h, leaving an
empty husk that will be removed in the next patch.
The NOR driver structure is an implementation detail, so move it into
its own private header file <flash/nor/driver.h> along with helper
declaration for finding them by name.
