Giving the example of STM32WL55x the examine log is the following:
Info : stm32wlx.cpu0: hardware has 6 breakpoints, 4 watchpoints
Info : stm32wlx.cpu1: hardware has 4 breakpoints, 2 watchpoints
After this change the examine log becomes:
Info : stm32wlx.cpu0: Cortex-M4 r0p1 processor detected
Info : stm32wlx.cpu0: target has 6 breakpoints, 4 watchpoints
Info : stm32wlx.cpu1: Cortex-M0+ r0p1 processor detected
Info : stm32wlx.cpu1: target has 4 breakpoints, 2 watchpoints
Change-Id: I1873a75eb76f0819342c441129427b38e984f0df
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6553
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some MCUs (e.g. the STM32F3) directly expose the internal reset line to
an external pin. When this signal is driven by a push/pull line, it can
actually be inhibited by the external driver. This results in a setup
where the MCU cannot reset itself, for example, by a watchdog timeout or
a sysreset request. To fix this condition, support for open drain output
on the SRST line is required.
Note that because `reset_config srst_open_drain` is the default, all
users of this adapter will switch over to an open drain output unless
explicitly configured otherwise.
Signed-off-by: Alex Crawford <openocd@code.acrawford.com>
Change-Id: I89b39b03aa03f826ed3c45793412780448940bcc
Reviewed-on: https://review.openocd.org/c/openocd/+/6559
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
1. Use TCP_NODELAY, which makes things twice as fast.
2. Get rid of a bunch of unnecessary socket block/non-block calls, which
improves speed another 10% or so.
Change-Id: I415db5746d55374a14564b1973b81e3517f5cb67
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6534
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The jimtcl API Jim_GetCommand() sets an error message when the
command is not found and flag JIM_ERRMSG is set.
OpenOCD is checking if the command has already been registered,
thus 'command not found' is the desired case.
Pass flag JIM_NONE to prevent jimtcl from setting the error
message.
Change-Id: I3329c2f8722eda0cc9a5f9cbd888a37915b46107
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6562
Tested-by: jenkins
Commit dc7b32ea4a ("armv7m_trace: get rid of the old tpiu code")
is not handling correctly the old 'tpiu' command if it is run
during the config phase (before command 'init').
Move the call to the old event handler 'trace-config' in function
jim_arm_tpiu_swo_enable(), so it is correctly executed after
'init'.
Add the call to the old event handler 'trace-config' also during
jim_arm_tpiu_swo_disable(), to match the old behaviour.
Add more information while alerting that the event 'trace-config'
is deprecated.
Change-Id: If831d9159b4634c74e19c04099d041a6e2be3f2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: dc7b32ea4a ("armv7m_trace: get rid of the old tpiu code")
Reviewed-on: https://review.openocd.org/c/openocd/+/6561
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
The initial version of the table dap_part_nums contains only the
part number of the device and not the manufacturer ID.
This causes collisions between devices with same part number but
from different manufacturer.
The table has been extended to include the manufacturer JEDEC code
in commit 2f131d3c30 ("ARM ADIv5: CoreSight ROM decode part
number and designer id").
For two old/legacy table's entries reported without manufacturer
code it was defined a special ANY_ID manufacturer, meaning skip
the check for manufacturer!
The two legacy entries report the comment "from OMAP3 memmap", and
thanks to the associated string has been possible through Google
to identify a Master Report [1] about using OpenOCD with the OMAP3
in a BeagleBoard. The ROM table is printed with OpenOCD command
"dap info 1" at page 8 and reports the Peripheral ID required to
extract the manufacturer ID that, out of any surprise, belong to
Texas Instruments.
Set the two missing manufacturer ID to Texas Instruments JEDEC
code.
Remove the now redundant definition and use of ANY_ID.
While revisiting this old code, remove also the useless comment
"0x113: what?". It was introduced in commit ddade10d4a ("ARM
ADIv5: "dap info" gets more readable") and from the same dump in
[1] it's clearly another element in OMAP3. It is listed as entry
0x8 in the ROM table and there is no further info available.
OpenOCD will anyway list it as:
Designer is 0x017, Texas Instruments
Part is 0x113, Unrecognized
Another link https://elinux.org/BeagleBoardOpenOCD reports the
text "Part number 0x113: This is ????", which sounds familiar!
No public document from Texas Instruments reports what is this
device at address 0x54012000.
[1] Warren Clay Grant - University of Texas at Austin
"Implementation of an Open Source JTAG Debugging Development
Chain for the BeagleBoard ARM® Cortex A-8" - May 2012
Link: https://repositories.lib.utexas.edu/bitstream/handle/2152/ETD-UT-2012-05-5478/GRANT-MASTERS-REPORT.pdf
Change-Id: I7e007addbb5c6e90303e4e8c110c7d27810fbe9c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6454
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Extract new part numbers from Arm Cortex-R52 Processor Technical
Reference Manual Revision r1p3 and add them to the array
dap_partnums.
Change-Id: I8020f36de587951af60422ef33d7e438dc7d9d53
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6451
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Extract new part numbers from ARM CoreSight System-on-Chip SoC-600
Technical Reference Manual Revision r4p1 and add them to the array
dap_partnums.
Change-Id: I88d8aa3c084f6e832b75032e75bfb6d377a08360
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6450
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
For readability, move in a separate function the decoding and the
display of devtype register.
The function will be reused with ADIv6.
Split from change https://review.openocd.org/6077/
Change-Id: I7a26a2c9759d5db5f9acfae5c169b90b3deb2f18
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6448
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The complete AP type should include 'class' and 'manufacturer'.
Cleanup the definition of AP type from AP_REG_IDR register.
Include the check of 'class', together with manufacturer and type.
Add the new MEM-AP from ARM IHI0074C.
Change-Id: Ic8db7c040108ba237b54f73b1abe24b8b853699b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6447
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Several magic numbers related to ARM CoreSight specification
IHI0029E are spread around OpenOCD code.
Define through macros the ARM CoreSight magic numbers and collect
them in a single include file.
Use the new macros wherever possible.
Change-Id: I9b0c1c651ce4ffbaf08d31791ef16e95983ee4cb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6446
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
The include file 'armv7m.h' includes 'arm_adi_v5.h' only to get
the definition of 'struct adiv5_ap', but doesn't need the struct
content.
Reducing the cross dependencies speeds-up the compile time during
code development by avoiding re-compiling file.
Relax the dependency by locally declaring 'struct adiv5_ap' in
'armv7m.h' and remove the include of 'arm_adi_v5.h'.
Fix the other files that have now lost the includes file that
'arm_adi_v5.h' depends from.
Change-Id: Ic0d40b17db6045fa43f348bda83eaf211a6b347d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6468
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This partially reverts commit 1247eee4e6.
There is no reasonable use cases where work-area should be enabled
and working, and it can't be used for the flash loader.
Instead of introducing driver specific property, users can disable
flash load by disabling work-area, for example by setting it to 0.
But still we keep the function stm32l4_write_block_without_loader
to be used when workarea is not available (no sufficient size or zero)
Change-Id: Ibb046c74df354c6067bac978e8ef7efb47d9fd2b
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6569
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
For STM32L552xC devices with 256K flash:
dual bank mode is activated if DB256 is set
page size is 2KB if DBANK is set
For parts with 512K (aka STM32L5x2xE):
DBANK controls both of dual/single bank mode and page size as well.
Change-Id: I8be668d5552fefe81acffaf2e3e35ef5e938162e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Patrik Bachan <diggit@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/317/
Reviewed-on: https://review.openocd.org/c/openocd/+/6538
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
the echo command is managed through command handler and not jim_handler
to be consistent rename the handler from jim_echo to handle_echo
and update the return values
Fixes: 4747af362d (JIM: document "echo" command)
Change-Id: I5ae87ea802d8430b573fb83daa6b35490b5d5775
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6549
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been
disabled. This PID has been observed on a Nucleo-G431RB board.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976
Reviewed-on: https://review.openocd.org/c/openocd/+/6555
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We are already at the limit for the number of VID/PID pairs declared
in stlink.cfg and stlink-dap.cfg. Increase the maximum number of pairs
from 8 to 16 to make room for a few more devices.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Ifad8e7ef67b930edbb5421730f00eb3390812f06
Reviewed-on: https://review.openocd.org/c/openocd/+/6554
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
NULL is defined as 'void *'.
There is no need to cast NULL while assigning it to a pointer.
Change-Id: Ibaf18e5d47329707ec9c1c184cd4bba2e8e702ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6540
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
The NULL pointers preceded by cast where not detected by the
scripting tools looking for NULL pointer comparison.
Remove them and, while there, further simplify the code and apply
the other coding style rules.
Change-Id: Ia7406122e07ef56ef311579ab0ee7ddb22c8e4b5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6539
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
change the gerrit server address from http://openocd.zylin.com to the new
address in order to avoid re-directions.
Change-Id: I76e128c277f63783d1a6f63a6a387aa838f51f80
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6481
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
do not force the presence of the reset line, since some custom boards
may do not contain the reset line.
Change-Id: I031ab34012b34a1b49def9db16461f9de0ae29cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Fleck <fleckz@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/316/
Reviewed-on: https://review.openocd.org/c/openocd/+/6506
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
stm32l4_work_area struct is shared between the loader and stm32l4x flash driver
'*wp' and '*rp' pointers' size is 4 bytes each since stm32l4x devices have
32-bit processors.
however when used in openocd code, their size depends on the host
if the host is 32-bit, then the size is 4 bytes each.
if the host is 64-bit, then the size is 8 bytes each.
to avoid this size difference, change their types depending on the
usage (pointers for the loader, and 32-bit integers in openocd code).
Change-Id: I0a3df4bb4bf872b01cdb9357eb28307868d7d469
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6556
Tested-by: jenkins
Reviewed-by: Yestin Sun <sunyi0804@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This works well with gdb on RISC-V, since hardware breakpoints are
per-core and gdb thinks that targets are really processes on a machine.
Are there targets where this is a bad idea? Should the target definition
specify whether this behavior is desired or not?
Change-Id: Ia32be2707b04347fd8bf2ca6fbb2b0ceaad3704a
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6528
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
CPU2 (Cortex-M0+) is supported only with non-hla adapters because it is on AP1.
Using HLA adapters armv7m.debug_ap is null, and checking ap_num triggers
a segfault.
Change-Id: I501f5b69e629aa8d2836b5194063d74d5bfddb12
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Fixes: https://github.com/STMicroelectronics/OpenOCD/issues/6
Reviewed-on: https://review.openocd.org/c/openocd/+/6535
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
add the target assigned to the flash bank at creation
this is useful in daisy chains, to filter out the target banks.
Change-Id: Ic39e44914e34bb62991783762e5a65ef8871e82f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6426
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The 'flash list' command returns the driver name as flash name which seems
to be incorrect, the proposal is:
- to fix this by returning the flash name
- and add a new item 'driver' in the returned list
example:
before the change
> flash list
{name stm32l4x base 134217728 size 0 bus_width 0 chip_width 0}
{name stm32l4x base 201326592 size 0 bus_width 0 chip_width 0}
{name stm32l4x base 200933376 size 0 bus_width 0 chip_width 0}
after the change
> flash list
{name stm32l5x.flash_ns driver stm32l4x ...}
{name stm32l5x.flash_alias_s driver stm32l4x ...}
{name stm32l5x.otp driver stm32l4x ...}
Change-Id: I6d307b73c457549981a93c260be344378719af82
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6425
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
known boards are NUCLEO-G431KB, NUCLEO-G431RB and NUCLEO-G474RE
note: this work safely with B-G431B-ESC1, B-G474E-DPOW1,
STM32G474E-EVAL and STM32G484E-EVAL
Change-Id: I132a97e1816620b182983edc8a4b272b52b9241d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5484
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
known boards are NUCLEO-G031K8, NUCLEO-G070RB, NUCLEO-G071RB
note: this work safely with STM32G0316-DISCO, STM32G071B-DISCO
and STM32G081B-EVAL
Change-Id: I483b6f44409228cd8c2c97b3c560927d1645c517
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5483
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This version of jimtcl:
- fixes memory leak in API Jim_CreateCommand();
- fixes 'make distcheck';
- uses single-argument syntax for 'expr'.
With the 'expr' syntax already fixed in all the tcl scripts in
OpenOCD, let's use the latest jimtcl to check it and anticipate
any further issues.
By using this version, the workaround for the memory leak and for
distcheck can be reverted.
Change-Id: I58e1bdc752a728f1b479de1c55067b698e817ef5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6226
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
All the scripts distributed with OpenOCD are already compliant
with the new syntax.
To avoid breaking user script, introduce a replacement for 'expr'
command that handles the old syntax while issuing a deprecated
warning.
This change should be part of OpenOCD v0.12.0, then reverted.
Change-Id: Ib08aa8ebcb634c81a3ce9d24fb4938b0418c947c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6510
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
STM32WB1x devices has a single flash bank up to 320 KB (page 2KB)
note: STM32WB5x/WB3x are single banks as well but do have 4KB as page size.
note: remove the assert that checks if max_mages is power of two, because
STM32WB1x flash size is not a power of 2
Change-Id: Ib514cf989ecb819d25d1c4a65d641d0a1a3d9f18
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6129
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this device has single bank flash architecture up to 64KB (page 2KB)
reference: RM0444 rev 5
Change-Id: Ia213c01accb950fcbb7519e08057dae11b4443dd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6128
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
switching to C loader instead of the assembly version will enhance readability
will reduce the maintenance effort.
besides the switch to C loader, we added a new parameters to the loader
like flash_word_size and flash_sr_bsy_mask in order to support properly
STM32U5x and STM32G0Bx/G0Cx in dual-bank mode.
Change-Id: I24cafc2ba637a065593a0506eae787b21080a0ba
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6109
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
instrument the telnet_move_cursor to detect when there is no change
of cursor position and if the requested new position is out of bounds.
Change-Id: I24da877e538a458da6d2f8ddc2a681eee404d2cb
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6441
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
like in terminal 'CTRL+C':
- keeps the line content so the user can refer to it (like copy/paste)
- marks the line with '^C', as hint that the command was not executed
- permit the user to write a new command
Change-Id: Ib784c827d64fdc439a35db461d8387a62d3bfbbf
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6439
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Tarek BOCHKATI
Alex Crawford
Tim Newsome
Antonio Borneo
Kevin Burke
Oleksij Rempel
Florian Zaruba
Andreas Sandberg
Yasushi SHOJI
Marc Schink
Wealian Liao