- Use new jtag_state_name() instead of global tap_state_strings[]
git-svn-id: svn://svn.berlios.de/openocd/trunk@1240 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- updated missing jtag dongle url's in texi
- reformat and remove whitespace from last commit
git-svn-id: svn://svn.berlios.de/openocd/trunk@1227 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- cleaned up headers to match rest of code
- added missing svn props for previously added files
git-svn-id: svn://svn.berlios.de/openocd/trunk@987 b42882b7-edfa-0310-969c-e2dbd0fdcd60
from pre/post_reset event scripts. Adding the second parameter was
a mistake seen in retrospect. this gives precise control in post_reset
for *when* the post reset speed is set. The pre_reset event was
added *after* the second parameter to jtag_khz/speed
- the target implementations no longer gets involved in the reset mode
scheme. Either they reset a target into a halted mode or not.
target_process_reset()
detects if the reset halt failed or not.
- tcl target event names are now target_N_name. Mainly internal
at this early stage, but best to get the naming right now.
- added hardcoded reset modes from gdb_server.c. I don't know precisely what
these defaults should be or if it should be made configurable. Perhaps some
hardcoded defaults will do for now and it can be made configurable later.
- bugfix in cortex_m3.c for reset_run_and_xxx?
- issue syntax error upon obsolete argument in target command instead of
printing message that will surely drown in the log
git-svn-id: svn://svn.berlios.de/openocd/trunk@849 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This address the >32 bit problem with drscan
also added a check for bypass in the execute since this will manifest itself
as a memory corruption when this check helps to debug the problem alot easier
git-svn-id: svn://svn.berlios.de/openocd/trunk@794 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- drscan is now a low level tcl command:
execute DR scan <device> <num_bits> <value> <num_bits1> <value2>
- removed obsolete partial command text support
git-svn-id: svn://svn.berlios.de/openocd/trunk@791 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- TAP reset without TRST shall be called TLR (stands for test-logic-reset, named after the TAP state it ends is) rather than tms (test-mode-select)
- some comments changed to /* C coding style */
git-svn-id: svn://svn.berlios.de/openocd/trunk@717 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- lower jtag speeds (higher divisor) was used, TDI was not changed on falling TCK edge as it should
- reset signal was release upon any TMS transition, making it impossible to use reset halt
- added khz() and speed_div() functions
git-svn-id: svn://svn.berlios.de/openocd/trunk@716 b42882b7-edfa-0310-969c-e2dbd0fdcd60
And not needed for Windows. Hopefully it will not break a Linux build.
git-svn-id: svn://svn.berlios.de/openocd/trunk@684 b42882b7-edfa-0310-969c-e2dbd0fdcd60
J-Link USB Protocol specification
- added functionality to jlink_init to display the version.
git-svn-id: svn://svn.berlios.de/openocd/trunk@675 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Work in progress to allow launching GDB/telnet server *before* jtag
chain enum, validate & examine
git-svn-id: svn://svn.berlios.de/openocd/trunk@569 b42882b7-edfa-0310-969c-e2dbd0fdcd60
to daemon_startup(still supported).
- print warning if srst and trst change state at the same time when srst_and_trst
is seperate
- reset now performs a trst, examines and validates the jtag chain before targets
assert reset
- if startup fails to examine and validate the jtag chain, try a reset before
trying again
git-svn-id: svn://svn.berlios.de/openocd/trunk@552 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix generic bitbang code to allow scans to end in Shift-[ID]R
- several CFI fixes (thanks to Michael Schwingen):
- buffer overflow when converting target code in cfi_intel_write_block -
cfi_fix_code_endian needs the number of words, not bytes, as size
argument.
- Spansion flash write was completely broken on big-endian targets - I
borrowed mechanisms from the intel driver, and moved some common code
into the cfi_command_val helper function. There is still more common code
that might be cleaned up.
- the buffer size check in cfi_write was broken for spansion flashes, where
cfi_write_words is not implemented. cfi_write_words is no only called if
the flash does have a buffer size >1.
- "flash info" printed CFI status information for non-CFI flashes, which is
confusing. It now only prints those when a real CFI flash is detected.
git-svn-id: svn://svn.berlios.de/openocd/trunk@517 b42882b7-edfa-0310-969c-e2dbd0fdcd60
is post reset = reset speed.
- removed infinite loop's and exit()'s upon poor arm7/9 communication
- cleaned up error messages a bit. Push ERROR() up into fn's that
fail and can say something meaningful about what failed.
git-svn-id: svn://svn.berlios.de/openocd/trunk@511 b42882b7-edfa-0310-969c-e2dbd0fdcd60
that all the jtag_add_xxx() are indeed intended to do the same thing.
git-svn-id: svn://svn.berlios.de/openocd/trunk@504 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- hopefully clarified the difference between TRST and TMS reset.
- added DEBUG() statements w.r.t. state changes
- TRST released and moving out of TAP_TLR are completely
different events. Only TRST released has a DEBUG() statement
git-svn-id: svn://svn.berlios.de/openocd/trunk@496 b42882b7-edfa-0310-969c-e2dbd0fdcd60
fail for two of it's return codes. A little bit weird, but compatible with
existing codebase.
- tightend up error handling. Since the jtag_xxx() is a queue that is either
executed as things are added(hw queue) or a software queue, then
errors can only be caught during jtag_execute_queue(). No error
code is therefore returned from the queuing fn's.
git-svn-id: svn://svn.berlios.de/openocd/trunk@492 b42882b7-edfa-0310-969c-e2dbd0fdcd60
are up and running. The examination and validation is actually
"optional" from the point of view of GDB + telnet servers.
Multiple targets should work fine with this.
- jtag_speed is dropped(divisor is increased), if jtag examination and
validation fails.
- the chain is validated 10x to catch the worst jtag_speed offences
- added LOG_SILENT that can be used to shut up log. Feeble
ersatz for try+catch.
- GDB register packets are now always replied in order to make sure
that GDB connect works. If the target is not halted, then these
packets contain dummy values.
git-svn-id: svn://svn.berlios.de/openocd/trunk@483 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added a check to jtag_add_pathmove() for legal path transitions
- tweaked jtag.h docs a little bit
- made some jtag bypass tests _DEBUG_JTAG_IO_
git-svn-id: svn://svn.berlios.de/openocd/trunk@448 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Passes 94kBytes/s regression test.
Works with str912, which relies on bypass
git-svn-id: svn://svn.berlios.de/openocd/trunk@447 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Small cosmetic fixes in the license header to make them all look the
same, fix some typos, update README.
git-svn-id: svn://svn.berlios.de/openocd/trunk@396 b42882b7-edfa-0310-969c-e2dbd0fdcd60
this patch fixes an issue in jtag_init - shall not reset jtag to NULL.
This causes jtag interface (USB device) not to be closed properly if jtag chain validation fails.
Once the underlaying jtag interface is initialized, jtag pointer shall be left untouched,
even in case of an error, so that proper cleanup can be done, see exit_handler in openocd.c
git-svn-id: svn://svn.berlios.de/openocd/trunk@372 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- bugfix in server.c
- removed unused parameter from jtag_add_ir_scan et al. This
wasn't necessary in hindsight but anyway.
- arm11 source committed but not not in Makefile.am/target.c for now.
git-svn-id: svn://svn.berlios.de/openocd/trunk@341 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- some more flash cleanup of checking halted state
- moved output handler into options.c
- very slightly tweaked server.c to make it a bit more compatible with eCos
- retired arch_state. Not quite sure how I managed to leave that out last time.
git-svn-id: svn://svn.berlios.de/openocd/trunk@338 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Allow all commands to be executed during config stage
- Help now works for config commands
- make var args handling follow the rules more closely
Thanks Øyvind Harboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@305 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- arm_simulate_step called incorrect arm_evaluate_opcode when in thumb mode
git-svn-id: svn://svn.berlios.de/openocd/trunk@254 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- native win32 now handles WSAECONNRESET - no longer exits openocd
- qCRC packet now works correctly under cygwin (gdb compare-sections command)
- removed __USE_GNU define from gdbserver.c
- gdb qSupported packet is now handled, with this we are able to tell gdb packet size, memory map of target
- added new target script gdb_program_config - called before gdb flash programming
- new gdb server command gdb_memory_map (enable|disable> - default is disable
- new gdb server command gdb_flash_program (enable|disable> - default is disable
- gdb flash programming supported - vFlash packets
- image_elf_read_section now does not clear any remaining data, this was causing the gdb checksum to fail with certain files
- reformat of usbprog.c
- memory leak in command_print fixed
- updated texi doc to include new commands
- added gdb programming section to docs
git-svn-id: svn://svn.berlios.de/openocd/trunk@246 b42882b7-edfa-0310-969c-e2dbd0fdcd60
flash verify_image and flash erase_address.
- added patch for new parport_write_on_exit command.
Even this patch will fix some memory leaks.
(thanks too oyvind and Spen for these patches)
git-svn-id: svn://svn.berlios.de/openocd/trunk@240 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Reducing stack usage for recursive scripts
- Do not exit on bogus arguments to reset_config. No longer exit the application upon bogus arguments to reset_config, but return errors.
thanks to Øyvind Harboe for these patches.
git-svn-id: svn://svn.berlios.de/openocd/trunk@226 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added patch which fixes a crash upon flash write error
- added patch which will improve the reset handling when
SRST is tied to TRST
(thanks to Oyvind Harboe for these patches)
git-svn-id: svn://svn.berlios.de/openocd/trunk@218 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- corrected array overrun in armv7m.c
- corrected breakpoint memory allocation bug
- image read now uses fgets, vastly improves reading of large files
- improved hex file reading, support for Linear Address Record added
git-svn-id: svn://svn.berlios.de/openocd/trunk@208 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- adds support for the Altium universal JTAG cable
- adds support for "wiggler2" cable (basically a wiggler with added LED, documentation coming soon)
- adds LED support. The LED is turned on during data transfer - works fine on Altium and wiggler2.
- adds PORT_EXIT pattern that is written to port when exiting, in order to turn off power on cables that get their power from parallel port data lines
- move port writes (with the system-specific ifdefs) to one central function
- increased image cache size to 2KB (might require more adaptive cache handling, e.g. LRU)
git-svn-id: svn://svn.berlios.de/openocd/trunk@204 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- usbprog update (thanks to Benedikt Sauter)
- added embeddedice_send and _handshake functions (thanks to Pavel Chromy)
- added support for 4, 8 and 16 bit ports to etb.c
git-svn-id: svn://svn.berlios.de/openocd/trunk@203 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- use 'etm trigger_percent' setting when programming ETB trigger count
- fixed some small bugs in ETM trace analysis
- fixed minor bug in flash writing (thanks to Pavel Chromy)
git-svn-id: svn://svn.berlios.de/openocd/trunk@197 b42882b7-edfa-0310-969c-e2dbd0fdcd60
--enable-presto_ftd2xx and --enable-presto_libftdi
- completed trace point support for use with ARM7/9 DCC
- completed debug message output with support for HEX dumps (1, 2 or 4 byte quantities)
- fixed bug in delete_debug_msg_receiver (thanks to Pavel Chromy)
- fixed bug in image_add_section (thanks to Pavel Chromy)
- at91sam7 sector erase reworked (thanks to Pavel Chromy)
- merge consecutive sections during flash image write to work around possible section alignment issues with LPC2000 targets
git-svn-id: svn://svn.berlios.de/openocd/trunk@194 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- make ep93xx and at91rm9200 bitbang JTAG interfaces dependant on ARM host (thanks to Vincent Palatin)
- various whitespace fixes
- removed various warnings
- add support for Debian GNU/kFreeBSD (thanks to Uwe Hermann)
- fix OpenOCD compilation for various platforms (thanks to Uwe Hermann and Vincent Palatin)
- switched order of JTAG chain examination and validation (examine first, then multiple validation tries even if examination failed)
- added target_request subsystem to handle requests from the target (debug messages and tracepoints implemented, future enhancements might include
semihosting, all ARM7/9 only for now)
- added support for GDB vFlashXXX packets (thanks to Pavel Chromy)
- added support for receiving data via ARM7/9 DCC
- reworked flash writing. the 'flash write' command is now deprecated and replaced by 'flash write_binary' (old syntax and behaviour) and 'flash
write_image' (write image files (bin, hex, elf, s19) to a target).
- added support for AMD/ST/SST 29F400B non-cfi flashes
git-svn-id: svn://svn.berlios.de/openocd/trunk@190 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- increase memory pseudo-image cache size to 1024 byte for improved trace analysis performance
- added OpenOCD+trace as an ETM capture driver example implementation
- new usbprog driver (thanks to Benedikt Sauter)
git-svn-id: svn://svn.berlios.de/openocd/trunk@186 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix multiple reads from FT2232 into same buffer location (thanks to Magnus Lundin)
- retry JTAG chain validation (thanks to Magnus Lundin)
- reworked GDB packet input handling (thanks to Pavel Chromy)
- output error message when setting a watchpoint failed
- removed duplicate out-of-bounds check in at91sam7.c (thanks to Pavel Chromy)
git-svn-id: svn://svn.berlios.de/openocd/trunk@181 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for usbprog (thanks to Benedikt Sauter)
- make OpenOCD listen for WM_QUIT messages on windows (thanks to Pavel Chromy)
- register at_exit handler to do necessary unregistering (thanks to Pavel Chromy)
- added dummy ETM capture driver to allow ETM to be registered without a capture driver
git-svn-id: svn://svn.berlios.de/openocd/trunk@180 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for scans coming from or ending in Shift-DR or Shift-IR to bitbang code (required for XScale debugging)
- cleaned up errror handlers. only use when there's a catchable error
- fix segfault when etm was configured without a valid driver
git-svn-id: svn://svn.berlios.de/openocd/trunk@176 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- reworked etm/etb into a generic etm part with trace capture drivers (currently only etb supported)
- added XScale debug handler binary to repository
- added Thumb disassembling (thanks to Vincent Palatin for this patch)
- added support for non-CFI compatible flashes to cfi driver (currently only SST39VFxxx devices supported)
This checkin is experimental, not suitable for general use
git-svn-id: svn://svn.berlios.de/openocd/trunk@155 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed several uses of uninitialized bits (Thanks to Vincent Palatin for finding and fixing these bugs)
git-svn-id: svn://svn.berlios.de/openocd/trunk@145 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- output all of EmbeddedICE version register in error message
- update OpenOCD's idea of the current core mode, and immediately change core mode, on CPSR changes
- added support for CFI cmdset 0002 (patch by Andrew Dyer, thanks a lot)
- enhanced CFI cmdset 0002 support to Atmel AT49 flashes (thanks to Joerg Krein for providing test hardware)
git-svn-id: svn://svn.berlios.de/openocd/trunk@138 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed some compiler warnigns in amt_jtagaccel.c, bitbang.c, parport.c
- free working area and register stuff if str7x block write algorithm failed
- check PC after exiting a target algorithm in armv4_5.c
git-svn-id: svn://svn.berlios.de/openocd/trunk@135 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed compiler warnings throughout the code (thanks to Vincent Palatin for this patch)
- added support for accessing ETB (embedded trace buffer) registers
git-svn-id: svn://svn.berlios.de/openocd/trunk@134 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for reading IHEX files (through fileio)
- load/dump_binary renamed to the more generic load/dump_image <file> <address> ['bin'|'ihex']
- added NAND framework (preliminary)
- added support for the LPC3180 SLC and MLC NAND controllers (preliminary)
- fix initialization for parport
- gw16012 fixes/cleanups
- added EmbeddedICE version 7 (preliminary, reported on two LPC23xx devices so far)
- added 'arm7_9 etm <target#>' configuration command to enable access to the ETM registers
git-svn-id: svn://svn.berlios.de/openocd/trunk@132 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- complain about identify_chain scan with all bits one (jtag communication problem)
- add 0x80000 as a valid size for lpc2000_v2 flash banks (previously only the user accessible 0x7d000 were valid)
git-svn-id: svn://svn.berlios.de/openocd/trunk@129 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix infinite recursion in target_init_handler (thanks to jw and Magnus Lundin)
- fix CFI flash handlign with buswidth < 32bit (thanks to Daniele Orio for reporting this)
- add support for reading JTAG device id (currently only as debug output on startup)
- cleaned up handling of EmbeddedICE registers. Supported functionality and register size now determined by EmbeddedICE version number.
- small cleanups/fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@124 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed bug in jtag.c where JTAG command type was wrong for PATHMOVE commands
- added lattice ISP cable (experimental)
- properly initialize parallel port (clear tristate bit)
- fixed jtag/Makefile.am that failed with some versions of autotools
- print error number if read() in gdbserver.c failed on Windows
- fixed handling of opcodes with bits 27-25 b011 (comment was correct, code had a bug)
- added support for AT91SAM7SE internal flash
git-svn-id: svn://svn.berlios.de/openocd/trunk@122 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for loading .bit files into Xilinx Virtex-II devices
- added support for the Gateworks GW16012 JTAG dongle
- merged CFI fixes from XScale branch
- a few minor fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@116 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- several small fixes
- retry reading from a FT2232 device on incomplete reads
git-svn-id: svn://svn.berlios.de/openocd/trunk@110 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for using Luminary Micro development board 'evb_lm3s811' as a JTAG interface (thanks to Magnus Lundin)
git-svn-id: svn://svn.berlios.de/openocd/trunk@106 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- correctly handle ft2232_device_desc and ft2232_serial when both are given at the same time
git-svn-id: svn://svn.berlios.de/openocd/trunk@104 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- redirect output from target event scripts (currently only reset) to the daemon output (INFO:)
- some minor fixes and enhancements
git-svn-id: svn://svn.berlios.de/openocd/trunk@103 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for AT91SAM7A devices (thanks to Magnus Lundin)
- updated README with pointer to Amontec's JTAGkeyTiny
git-svn-id: svn://svn.berlios.de/openocd/trunk@102 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- str75x flash support (Thanks to Spencer Oliver)
- correct reporting of T-Bit in CPSR (Thanks to John Hartman for reporting this)
- core-state (ARM/Thumb) can be switched by modifying CPSR
- fixed bug in gdb_server register handling
- register values > 32-bit should now be supported
- several minor fixes and enhancements
git-svn-id: svn://svn.berlios.de/openocd/trunk@100 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added access to ARM920T vector catch register (via generic register mechanism)
- don't disable linefills on ARM920T cores - this lead to lockups when accessing lines already contained in cache
- read content of ARM920T cache and tlb into file (arm920t read_flash/read_mmu commands)
- memory reading improved on ARM7/9, can be further accelerated with new "arm7_9 fast_memory_access enable" command (renamed from fast_writes)
- made in_handler independent from in field (makes the handler more flexible)
- added timeout to ft2232 when using D2XX library
- fixed STR7x protection bit handling on second bank (thanks to Bernard)
- added support for using the OpenOCD on AT91RM9200 systems (thanks to Anders Larsen)
- fixed AT91SAM7 flash handling when not running from 32kHz clock (thanks to Anders Larsen)
git-svn-id: svn://svn.berlios.de/openocd/trunk@90 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed small bug in str7x.c that printed an address instead of the target number in an error message
- added support for Olimex ARM-USB-OCD. The new ft2232 layout is called "olimex-jtag"
git-svn-id: svn://svn.berlios.de/openocd/trunk@87 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- unified 'ftd2xx' and 'ftdi2232' into a single interface 'ft2232'. The library used to access the hardware is choosen during configure with --enable-ft2232_ftd2xx or --enable-ft2232-libftdi.
git-svn-id: svn://svn.berlios.de/openocd/trunk@83 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- additional debug output when opening the parallel port
- fixed counting of available arm7/9 watchpoint units
- 'flash write' now displays elapsed time
git-svn-id: svn://svn.berlios.de/openocd/trunk@79 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Added state-move support to ftd2xx and bitbang JTAG drivers (required for XScale, possibly useful for other targets, too)
- various fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@78 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed bug in telnet history handling (patch from John Hartman, thanks)
- OpenOCD version has been changed from SVN revision number to date/time
git-svn-id: svn://svn.berlios.de/openocd/trunk@74 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix trunk build for mac os x (patch from Lauri Leukkunen, thanks)
- added check for host endianness, defines WORDS_BIGENDIAN on a big-endian host (e.g. mac os-x)
- fixed bug where endianness of memory accesses could be swapped on BE hosts
- added space for zero termination of ftd2xx_layout string (from Magnus Ludin, tahnks)
git-svn-id: svn://svn.berlios.de/openocd/trunk@73 b42882b7-edfa-0310-969c-e2dbd0fdcd60
