Without the change cortex_m_debug_entry() reads all registers
calling cortex_m_load_core_reg_u32() for each register with
a poor usage of JTAG/SWD queue.
It is time consuming, especially on an USB FS based adapter.
Moreover if target_request debugmsgs are enabled, DCB_DCRDR
is saved and restored on each register read.
This change introduces cortex_m_fast_read_all_regs()
which queues all register reads and a single dap_run() transaction
does all work.
cortex_m_fast_read_all_regs() reads all registers unconditionally
regardless register cache is valid or not. This is a difference
from the original cortex_m_debug_entry() code.
cortex_m_debug_entry times from -d3 log, Cortex-M4F and CMSIS-DAP
(Kinetis K28F-FRDM kit)
target_request | time [ms]
debugmsgs | without the change | with the change
---------------+--------------------+-----------------
disable | 186 | 27
enable | 232 | 29
Added checking of DHCSR.S_REGRDY flag. If "not ready" is seen,
cortex_m->slow_register_read is set and fallback to the old
register read method cortex_m_slow_read_all_regs() is used
instead of cortex_m_fast_read_all_regs().
Change-Id: I0665d94b97ede217394640871dc451ec93410254
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5321
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The include file 'armv7m.h' includes 'arm_adi_v5.h' only to get
the definition of 'struct adiv5_ap', but doesn't need the struct
content.
Reducing the cross dependencies speeds-up the compile time during
code development by avoiding re-compiling file.
Relax the dependency by locally declaring 'struct adiv5_ap' in
'armv7m.h' and remove the include of 'arm_adi_v5.h'.
Fix the other files that have now lost the includes file that
'arm_adi_v5.h' depends from.
Change-Id: Ic0d40b17db6045fa43f348bda83eaf211a6b347d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6468
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Patch generated automatically through the new checkpatch with
flags "--types COMPARISON_TO_NULL --fix-inplace".
This only fixes the comparisons
if (symbol == NULL)
if (symbol != NULL)
The case of NULL on the left side of the comparison is not tested.
Some automatic fix is incorrect and has been massaged by hands:
- if (*psig == NULL)
+ if (*!psig)
changed as
+ if (!*psig)
Change-Id: If4a1e2b4e547e223532e8e3d9da89bf9cb382ce6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6351
Tested-by: jenkins
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
Despite of assert(is_packed) clang static analyser complains on use
of the uninitialized offset variable.
Cross compiling with latest x86_64-w64-mingw32-gcc hits warnings
src/target/armv7m.c: In function ‘armv7m_read_core_reg’:
src/target/armv7m.c:337:54: error: ‘reg32_id’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
It happens because mingw32 defines assert() without the attribute
"noreturn", whatever NDEBUG is defined or not.
Replace assert(is_packed) by if (is_packed) conditional and call
assert(false) in the else branch.
Change-Id: Id3c7dcccb65106e28be200b9a4d2b642f4d31019
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6256
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
Change-Id: I4fea29f07f4d3b8b2578b538ef0eef5f1eea285f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5876
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Move primask/basepri/faultmask/control packing/unpacking from
cortex_m.c and hla_target.c to armv7m.c armv7m_read_core_reg()
and armv7m_write_core_reg() where also the FP 32/64-bit registers
conversion takes place.
Introduce a new hidden register ARMV7M_PMSK_BPRI_FLTMSK_CTRL
for packing/unpacking of special registers in the register cache.
The new packing/unpacking is endianess safe.
While on it improve returned error codes and LOG_ messages.
Just minimal changes in cortex_m.c and hla_target.c, will be
consolidated in the next patch.
Change-Id: Id51e764e243e54b5fdaadf2a202eee7c4bc729fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5863
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Make arm register id coherent with reg_list index.
Without this reg_list[ARMV7M_R12] was possible but
reg_list[ARMV7M_FPSCR] was out of bounds.
Remove unused items from reg_list index.
Change-Id: I84d3b5c496fc1839d07a5b74cb1fd1c3d4ff8989
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5862
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Define a new enum with DCRSR.REGSEL selectors.
Introduce armv7m_map_id_to_regsel() to unify mapping in one place.
Use DCRSR.REGSEL selectors for low level register read/write.
Change-Id: Ida0ccdfa9cdb1257a1900b8bfbf172b076374d39
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Bit 2 of control register is used if the processor includes the FP
extension
Change-Id: Ie21bc9de8cae5bad9d841e1908eff3aa0bb29d4b
Signed-off-by: Sylvain Chouleur <schouleur@graimatterlabs.ai>
Reviewed-on: http://openocd.zylin.com/5853
Reviewed-by: Sylvain Chouleur <sylvain.chouleur@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Introduce a variable 'size' and reduce the number of dereferencing
*reg_list_size by using the variable.
Change-Id: I3bdf1485a4ed8e34435e8acb3efd0df8d802508c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Introduce a new ERROR_TARGET_ALGO_EXIT as currently used
ERROR_TARGET_TIMEOUT should be reserved for the timeout only.
Do not load PC directly from CPU HW as the register value
has already been cached.
Change-Id: I0d3630da41fd021676789dc12b52545cc0432ba8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5329
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The fields core_type and core_mode use the same enum arm_mode
but encode different information, making the code less immediate
to read.
Use a different enum arm_core_type for the field core_type.
The code behavior is not changed.
Change-Id: I60f2095ea6801dfe22f6da81ec295ca71ef90466
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5258
Tested-by: jenkins
armv7m_get_core_reg() calls arm->read_core_reg()
arm->read_core_reg() expects the register number as an index
to core reglist, not an ARMv7M specific register code.
Use reg->number instead of armv7m_reg->num.
The change solves assert
src/target/armv7m.c:222: armv7m_read_core_reg: Assertion
`num < (int)armv7m->arm.core_cache->num_regs' failed.
when gdb 'info reg' is issued on a Cortex-M target and
no cortex_m_debug_entry() has been called since OpenOCD start
(target was halted before OpenOCD start).
Change-Id: I32a2294693ef979b613be93aeceb3b0eb06ee6df
Ticket: https://sourceforge.net/p/openocd/tickets/216/
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5203
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fix the write only out params TODO on armv7m.c
Fix conditional move depends on uninitialised value.
It was detected while programming a LPC8Nxx with a FTDI adapter.
valgrind --leak-check=full --show-leak-kinds=all --track-origins=yes
[...]
==8696== Conditional jump or move depends on uninitialised value(s)
==8696== at 0x16E4D3: buf_set_u32 (binarybuffer.h:52)
==8696== by 0x16E4D3: ftdi_swd_queue_cmd (ftdi.c:1206)
==8696== by 0x18D76D: swd_queue_ap_write (adi_v5_swd.c:271)
==8696== by 0x18E33B: dap_queue_ap_write (arm_adi_v5.h:382)
==8696== by 0x18E33B: mem_ap_write (arm_adi_v5.c:420)
==8696== by 0x197CD9: target_write_buffer_default (target.c:2176)
==8696== by 0x2464B3: armv7m_start_algorithm (armv7m.c:383)
==8696== by 0x246AEB: armv7m_run_algorithm (armv7m.c:330)
==8696== by 0x19D846: target_run_algorithm (target.c:814)
==8696== by 0x1DF3A6: lpc2000_iap_call.isra.3 (lpc2000.c:818)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== Uninitialised value was created by a heap allocation
==8696== at 0x4C2BBAF: malloc (vg_replace_malloc.c:299)
==8696== by 0x220EF9: init_mem_param (algorithm.c:30)
==8696== by 0x1DF247: lpc2000_iap_call.isra.3 (lpc2000.c:777)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== by 0x18ACDF: handle_flash_write_image_command (tcl.c:457)
==8696== by 0x1B7D99: run_command (command.c:623)
==8696== by 0x1B7D99: script_command_run (command.c:208)
==8696== by 0x1B7FD9: command_unknown (command.c:1033)
==8696== by 0x2E2D37: JimInvokeCommand (jim.c:10364)
==8696== by 0x2E3865: Jim_EvalObj (jim.c:10814)
==8696==
==8696== Conditional jump or move depends on uninitialised value(s)
==8696== at 0x16E506: buf_set_u32 (binarybuffer.h:52)
==8696== by 0x16E506: ftdi_swd_queue_cmd (ftdi.c:1207)
==8696== by 0x18D76D: swd_queue_ap_write (adi_v5_swd.c:271)
==8696== by 0x18E33B: dap_queue_ap_write (arm_adi_v5.h:382)
==8696== by 0x18E33B: mem_ap_write (arm_adi_v5.c:420)
==8696== by 0x197CD9: target_write_buffer_default (target.c:2176)
==8696== by 0x2464B3: armv7m_start_algorithm (armv7m.c:383)
==8696== by 0x246AEB: armv7m_run_algorithm (armv7m.c:330)
==8696== by 0x19D846: target_run_algorithm (target.c:814)
==8696== by 0x1DF3A6: lpc2000_iap_call.isra.3 (lpc2000.c:818)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== Uninitialised value was created by a heap allocation
==8696== at 0x4C2BBAF: malloc (vg_replace_malloc.c:299)
==8696== by 0x220EF9: init_mem_param (algorithm.c:30)
==8696== by 0x1DF247: lpc2000_iap_call.isra.3 (lpc2000.c:777)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== by 0x18ACDF: handle_flash_write_image_command (tcl.c:457)
==8696== by 0x1B7D99: run_command (command.c:623)
==8696== by 0x1B7D99: script_command_run (command.c:208)
==8696== by 0x1B7FD9: command_unknown (command.c:1033)
==8696== by 0x2E2D37: JimInvokeCommand (jim.c:10364)
==8696== by 0x2E3865: Jim_EvalObj (jim.c:10814)
Change-Id: I50f9a8c4516b686cf62ac3c76f47c53465e949da
Signed-off-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-on: http://openocd.zylin.com/4811
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without this change xxx_start_algorithm() writes all register
parameters no matter of their direction. It usually results
in writing of uninitialized reg_params[].value - possibly
reported by valgrind.
While on it fix the wrong parameter direction in
kinetis_disable_wdog_algo(). This bug did not have any
impact because of unconditional write of reg_params.
Change-Id: Ia9c6a7b37f77d5eb6e5f5463012dddd50471742b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4813
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
xPSR.T sets the processor to Thumb mode when set to 1. ARMv7-M only
supports execution of Thumb instructions, so it must always be set to 1.
If xPSR.T is set to 0 on armv7m, a usage fault is generated when a
instruction execution is attempted.
On armv7m, issuing a reset causes the vector table to be examined. PC
and xPSR.T are loaded from the vector table at byte offset 4. xPSR.T is
taken from the least significant bit this value, PC from the remaining
bits. This occurs even with `reset halt`, as the reset itself causes
this load to occur without the execution of any instructions.
As a result of this, following a reset with a "bad" value programmed in
the vector table, openocd would be unable to run algorithms on the
target, as running them would immediately result in a usage fault due to
xPSR.T being unset (0).
Allow algorithms to run regardless of the content of the vector table by
explicitly setting xPSR so that xPSR.T=1 prior to executing an
algorithm. One can think of this as openocd more closely emulating a
reset or branch instruction in executing it's algorithms.
Ticket: https://sourceforge.net/p/openocd/tickets/203/
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Change-Id: I4dc3427ab195d06c3fd780ea768027fefccc4c28
Reviewed-on: http://openocd.zylin.com/4658
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The new common semihosting code introduced a bug,
in certain conditions target->semihosting was
used without semihosting being initialised.
The solution was to explicitly test for
target->semihosting before dereferencing it.
Change-Id: I4c83e596140c68fe4ab32e586e51f7e981a40798
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4603
Tested-by: jenkins
Reviewed-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In 2016, ARM released the second edition of the semihosting specs
("Semihosting for AArch32 and AArch64"), adding support for 64-bits.
To ease the reuse of the semihosting logic for other platforms
(like RISC-V), the semihosting code was isolated from the ARM
target and updated to the latest specs.
The new code is already in use since January (in GNU MCU Eclipse
OpenOCD) and no problems were reported, neither for ARM nor for
RISC-V targets, after more than 7K downloads.
The 2 new files were formatted with uncrustify.
Change-Id: Ie84dbd86a547323bb8a5d24eab68fc7dad013d96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4518
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested on PSoC6 (Cortex-M0+ core), onboard KitProg2 in CMSIS-DAP mode,
adapter_khz=1000.
Plain read:
flash read_bank 0 /dev/null
takes 48 seconds.
erase_check without this change:
flash erase_check 0
takes horrible 149 seconds!!
And the same command with the change applied takes 1.8 seconds.
Quite a difference.
Remove the erase-value=0 version of algorithm as the new one can check
for any value.
If the target is an insane slow clocked CPU (under 1MHz) algo
timeouts. Blocks checked so far are returned and the next call
uses increased timeout.
Change-Id: Ic0899011256d2114112e67c0b51fab4f6230d9cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4298
Tested-by: jenkins
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
'flash erase_check' command runs a check algorithm on a target
if possible. The algorithm is run repeatedly for each flash sector.
Unfortunately every start and stop of the algorithm impose not negligible
overhead.
In practice it means checking is faster than plain read only for
sectors of size approx 4 kByte or bigger. And checking sectors
as short as 512 bytes runs approx 4 times slower than plain read.
The patch changes API call target_blank_check_memory() and related
to take an array of sectors (or arbitrary memory blocks).
Changes in target-specific checking routines are kept minimal.
They use only the first block from the array and process it by
the unchanged algorithm.
default_flash_blank_check() routine repeats target_blank_check_memory()
until all blocks are checked, so it works with both multi-block
and single-block based checkers.
Change-Id: I0e6c60f2d71364c9c07c09416b04de9268807f5e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4297
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Define a target_addr_t type to support 32-bit and 64-bit addresses at
the same time. Also define matching TARGET_PRI*ADDR format macros as
well as a convenient TARGET_ADDR_FMT.
In targets that are 32-bit (avr32, nds32, arm7/9/11, fm4, xmc1000)
be least invasive by leaving the formatting unchanged apart from the
type;
for generic code adopt TARGET_ADDR_FMT as unified address format.
Don't silently change gdb formatting here, leave that to later.
Add COMMAND_PARSE_ADDRESS() macro to abstract the address type.
Implement it using its own parse_target_addr() function, in the hopes
of catching pointer type mismatches better.
Add '--disable-target64' configure option to revert to previous 32-bit
target address behavior.
Change-Id: I2e91d205862ceb14f94b3e72a7e99ee0373a85d5
Signed-off-by: Dongxue Zhang <elta.era@gmail.com>
Signed-off-by: David Ung <david.ung.42@gmail.com>
[AF: Default to enabling (Paul Fertser), rename macros, simplify]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
This patch adds support for bridging semihosting to GDB's File-I/O
remote protocol extension. For the most part operations match up 1:1,
however some require a working area to complete successfully, namely
operations that devolve to read, stat, and gettimeofday.
A new command was added to enable support for fileio named `arm
semihosting_fileio`, which ensures that the default behavior remains
intact for those that prefer it.
Finally, redundant logging was removed from the target_arch_state
function; this permits ARM targets to quiesce log output when polling
for a fileio reply. This prevents filling the logs with halt/resume
messages when using semihosting fileio.
Change-Id: Ifbb864fc2373336a501cc0332675b887b552e1ee
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3566
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
struct flash_driver has a default_padded_value field that is similar,
but it can be changed by the user for the specific purpose of padding.
Add a new erased_value field and initialize it for all targets,
particularly stm32lx, xmc4xxx and virtual.
Use this value in core.c:default_flash_mem_blank_check(), the slow path.
Extend the target API to pass erased_value down to target code.
Adding an argument ensures that we catch all callers.
This allows us to merge xmc4xxx.c:xmc4xxx_blank_check_memory() into
armv7m:armv7m_blank_check_memory().
It further allows us to use default_flash_blank_check() in place of
xmc4xxx.c:xmc4xxx_flash_blank_check(), adding a potential slow path
fallback, as well as stm32lx:stm32lx_erase_check(), adding the potential
armv7m fast path with fallback to default_flash_mem_blank_check().
Fix a mips32 code comment while at it (zeroed -> erased).
The armv4_5 and mips32 target implementations will now error out if an
erase value other than 0xff is used, causing default_flash_blank_check()
to fall back to the default_flank_mem_blank_check() slow path.
Change-Id: I39323fbbc4b71c256cd567e439896d0245d4745f
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3497
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv7m_crc.inc and include it via preprocessor.
Change-Id: I4482c7acb8454de28bdf210d9f06c0720ada490a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3474
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Adapted from armv7m_checksum_memory().
Change-Id: I4e5950f568ed70a72a1dcfd77e3321110b17e1de
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3469
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Instead of documenting the file path as a comment and inline-commenting
the THUMB bytecode, include the hex array via preprocessor.
This assures the path is actually up-to-date and facilitates updating
the code.
Change-Id: Ieb0a7cd0bc14882ac96750f524616d9768a0c6f5
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3134
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This provides support for various trace-related subsystems in a
generic and expandable way.
Change-Id: I3a27fa7b8cfb111753088bb8c3d760dd12d1395f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2538
Tested-by: jenkins
This is runtime and valgrind tested with l0, l1 and f3 hla boards.
Change-Id: I49b0b042253d5f3bf216997f0203583db319fe23
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2516
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds the fpv4-sp-d16 registers to the armv7m register set.
The work is inspired by Mathias K but takes a different approach:
instead of having both double and single presicion registers in the
cache this patch works only with the doubles and counts on GDB to
split the data in halves whenever needed.
Tested with HLA only (on an STM32F334 disco board).
Currently this patch makes all ARMv7-M targets report an FPU-enabled
target description to GDB. It shouldn't harm if the user is not trying
to access non-existing FPU. However, the plan is to make this depend
on actual FPU presence later.
Change-Id: Ifcc72c80ef745230c42e4dc3995f792753fc4e7a
Signed-off-by: Mathias K <kesmtp@freenet.de>
[fercerpav@gmail.com: rework to fit target description framework]
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/514
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Ignoring the value parameter in that function makes its code rather
misleading. Also the only caller of it, armv7m_restore_context already
does the whole "buf_get_u32" conversion business, so using
'value' also removes the waste of doing the conversion twice.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I515979c314d9b59ee1065c55b5bb5747c7e93f01
Reviewed-on: http://openocd.zylin.com/2057
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
We changed the actual target name quite a while ago.
This changes the actual target function names/defines to also match
this change.
Change-Id: I4f22fb107636db2279865b45350c9c776e608a75
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1626
Tested-by: jenkins
Now that we support the target description format we do not need
these hacks anymore, we can now tell gdb what registers we support.
Change-Id: Ie774231d296420b35efcf708bc4435475c87ff5e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1617
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The was missed when the armv7m was moved over to using the std arm
core_cache, probably because it is disabled by default.
Change-Id: I2f5a18ef6dd783b36e8c29f4c52379104bda4583
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1138
Tested-by: jenkins
This makes sure we are using privileged mode when executing any loaders.
Change-Id: I18bf32ec92e1c76a66ab25e3712652bc3650b332
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1108
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek
Antonio Borneo
Marc Schink
Tarek BOCHKATI
Sylvain Chouleur
Marc Schink
Jean-Christian de Rivaz
Cody P Schafer
Liviu Ionescu
Matthias Welwarsky
Dongxue Zhang
Steven Stallion
Andreas Färber
Paul Fertser
Spencer Oliver
Andrey Smirnov
Hsiangkai Wang