This is supposed to replace big part of armv7m_trace.[ch], since
TPIU is not only the one implemented in Cortex-M3 and M4.
Change-Id: I7588d16cbefe9cdb371c52fb0aa5cdfb48518804
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5858
Tested-by: jenkins
Quote: The ST-LINK TCP server is an application to share the debug
interface of a single ST-LINK board among several host applications,
typically a debugging tool and a monitoring tool.
Note: ST-Link TCP server does not support the SWIM transport.
ST-LINK TCP server allows several applications to connect to the same
ST-Link through sockets (TCP).
To use ST-LINK TCP server:
- using stlink-dap : use 'st-link backend tcp [port]'
- using hla : use 'hla_stlink_backend tcp [port]'
the default port value is 7184
Change-Id: I9b79f65267f04b1e978709934892160e65bd2d6d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5633
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
OpenOCD is based on a single main loop that schedules all the
activities.
At the execution of a TCL command, the timestamp is checked to
eventually trigger the polling of the targets. This means that by
executing a TCL command the polling can be triggered and detect a
change of target's state.
When openocd 'resumes' a target, the target can halt again by
hitting a breakpoint.
The 'resumed' event handler is started just after the target has
been resumed, but it triggers a polling before the execution of
its very first instruction.
If the polling finds the target halted, it will run the 'halted'
event handler, that will then be executed 'before' the pending
'resumed' handler.
In case of gdb, a 'continue' command will restart the target but,
polling (and halt detection) executed before the end of the resume
process will hide the halt. As a consequence, the gdb will not be
informed of the halt and will remains waiting as if the target is
still running without showing the prompt.
This can be verified by running on the target a firmware with a
loop, run openocd with a dummy 'resumed' event, and let gdb to set
a breakpoint in the loop. A 'continue' command will cause the
target to halt again by hitting the breakpoint at the next loop
iteration, but gdb will loose it and will not return the prompt.
openocd -f board/st_nucleo_f4.cfg -c \
'stm32f4x.cpu configure -event resumed {echo hello}'
arm-none-eabi-gdb -ex 'target remote :3333' -ex 'b *$pc' -ex c
Disable the polling while executing target's resume().
Document it and provide hints to developers to cope with future
implementation.
Change-Id: I3be830a8e7c2ef6278617cb4547a4d676b0ddeb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Габитов Александр Фаритович <gabitov@planarchel.ru>
Reviewed-on: http://openocd.zylin.com/6074
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
We are talking about adapter connectivity in this chapter. It should
be "dongles" instead of "cables".
Change-Id: I7bd4307765517375caa2af86dfc929d0ef66c3e6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6040
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This adds some cosmetic changes to make the PDF User Manual look
proper.
Building it now requires Texinfo 5.0 which shouldn't be problematic
according to [0]. Commit 79fdeb37f4 is
effectively reverted.
[0] https://repology.org/project/texinfo/versions
Change-Id: I990bc23bdb53d24c302b26d74fd770ea738e4096
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5995
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This was flagged by lintian against the Debian package; the text stating
there are no invariant sections deviates from the official GNU wording.
Update it to match the text at the bottom of:
https://www.gnu.org/licenses/old-licenses/fdl-1.2.en.html
Change-Id: Ie222237a8eede24c1b71218b05e1513b74208a47
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/5974
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Real Time Transfer (RTT) is an interface specified by SEGGER based on
basic memory reads and writes to transfer data bidirectionally between
target and host.
Every target that supports so called "background memory access", which
means that the target memory can be accessed by the debugger while the
target is running, can be used.
RTT is especially of interest for targets which do not support Serial
Wire Output (SWO) (e.g. ARM Cortex-M0) or where using semihosting is
not possible (e.g. real-time applications) [1].
The data transfer is organized in channels where each channel consists
of an up- and/or down-channel. See [2] for more details.
Channels are exposed via TCP connections. One or more RTT server can be
assigned to each channel to make them accessible to an unlimited number
of TCP connections.
The current implementation does not respect buffer flags which are used
to determine what happens when writing to a full buffer.
Note that the implementation is designed in a way that the RTT
operations can be directly performed by an adapter (e.g. J-Link).
[1] https://devzone.nordicsemi.com/tutorials/6/
[2] https://www.segger.com/jlink-rtt.html
Change-Id: I8bc8a1b381fb74e08b8752d5cf53804cc573c1e0
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4055
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
The only code dealing with tftp in OpenOCD was in eCos build, code
already dropped in commit 39650e2273 ("ecosboard: delete
bit-rotted eCos code") almost 8 years ago.
Drop tftp related documentation too.
Change-Id: I0defc8f844e74c90894dca04a652dcc497a520e1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5913
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
When trace capturing the trace is enabled using 'tpiu_config internal'
(via the internal mode), OpenOCD can collect the trace buffers then append
it to a specified file or named pipe and propagate the trace to 'tcl_trace'
command.
This change is allowing OpenOCD to stream the captured trace over TCP.
When using this configuration OpenOCD acts like a server and multiple
clients can connect and receive the captured trace.
Example on STM32F7 running at 216MHz:
itm port 0 on
tpiu config internal :3344 uart off 216000000
Change-Id: Idea43e7e26e87b98a33da7fb9acf7ea50fe3b345
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5345
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The default way of working is to have a single GDB attached to one
target, so OpenOCD accepts only one connection to the GDB port of
each targets and rejects any further connection.
There are some barely safe use cases in which it could get useful
having a second GDB connection to the same target.
One such use case is while using GDB as a 'non-intrusive memory
inspector', as explained in the OpenOCD documentation.
One GDB can be left running an infinite loop to dump some memory
area, or even analysing the content, while keeping a second GDB
ready for user interaction or spot memory check.
Add a target configure option to specify the maximum number of GDB
connections allowed for that target, keeping the default to 1.
Change-Id: I4985a602e61588df0b527d2f2aa5b955c93e125e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5865
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
To avoid code duplication, reorganize the code to replace
cti_configure() with adiv5_jim_mem_ap_spot_configure().
Reorganize 'struct arm_cti_object' and its sub-'struct arm_cti'
moving DAP and mem-AP info in a 'struct adiv5_mem_ap_spot'.
Replace cti_configure() with adiv5_jim_mem_ap_spot_configure().
Deprecate the use of '-ctibase' in favor of '-baseaddr'.
Change-Id: I43740a37c80de67c0f5e4dc79c3400b91a12e9e8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5869
Tested-by: jenkins
These are all the changes from https://github.com/riscv/riscv-openocd
(approximately 91dc0c0c) made just to src/target/riscv/*. Some of the
new code is disabled because it requires some other target-independent
changes which I didn't want to include here.
Built like this, OpenOCD passes:
* All single-RV32 tests against spike.
* All single-RV64 tests against spike.
* Enough HiFive1 tests. (I suspect the failures are due to the test
suite rotting.)
* Many dual-RV32 (-rtos hwthread) against spike.
* Many dual-RV64 (-rtos hwthread) against spike.
I suspect this is an overall improvement compared to what's in mainline
right now, and it gets me a lot closer to getting all the riscv-openocd
work upstreamed.
Change-Id: Ide2f80c9397400780ff6780d78a206bc6a6e2f98
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5821
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Search in XDG_CONFIG_HOME as per XDG Base Directory Specification
in addition to $HOME/.openocd.
On Darwin, search in ~/Library/Preferences/org.openocd/ which
appears to be one of the conventional locations.
Make $OPENOCD_SCRIPTS highest priority on all platforms, previously
it was only higher on WIN32.
Update the documentation to reflect the search order.
Change-Id: Ibaf4b59b51fdf452712d91b47ea2b5312bb5ada9
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3890
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This driver provides support for Cadence JTAG BFM
The "jtag_dpi" driver implements a JTAG driver acting as a client for the
SystemVerilog Direct Programming Interface (DPI) for JTAG devices.
DPI allows OpenOCD to connect to the JTAG interface of a hardware model
written in SystemVerilog, for example, on an emulation model of
target hardware.
Tested on Ampere emulation with Altra and Altra Max models
Change-Id: Iaef8ba5cc1398ee2c888f39a606e8cb592484625
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5573
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Implementation largely taken from Nuvoton github
https://github.com/OpenNuvoton/OpenOCD-Nuvoton
Reset is still not fully compatible with OpenOCD framework.
Adapted to hidapi.
Change-Id: Ieb1791b1b7f0b444c15c9668f8f2bcf34975d48f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Reviewed-on: http://openocd.zylin.com/5720
Tested-by: jenkins
Reviewed-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Marc Schink <dev@zapb.de>
Add support for Nu-Link1 over usb hidapi and config file.
The original work is fetched from Nuvoton github.
Code cleanup, fix merge conflicts, compile and runtime issues.
Switch the code from libusb to hidapi, being the device HID based.
Add documentation.
Merge fixes for multi-word memory read.
Reset is not fully compatible with openocd framework; currently
the target is reset and then halt at openocd start.
Change-Id: I9738de4e26783ba462ea3e39ec32069fd5bb7d94
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5635
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Add threads support for RIOT (https://github.com/RIOT-OS/RIOT).
Original code is from Daniel Krebs.
Change-Id: I83fe3b91dd75949e800b5aea1015d8fa37b09c61
Signed-off-by: Daniel Krebs <github@daniel-krebs.net>
Signed-off-by: Vincent Dupont <vincent@otakeys.com>
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Reviewed-on: http://openocd.zylin.com/4256
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Remove occurrences of duplicated words in the documentation.
Change-Id: Ib6ef1607fc5e6387764be108b2b9c0c93ac10a62
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5754
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In case of GDB connection not using extended mode, issue a warning
message to suggest the user to switch using the extended mode.
Issue the message only once at each run of OpenOCD, to avoid too
much noise.
Update the documentation to suggest using extended mode.
Change-Id: I9326e84f748d5d7912d5a48f00f0fb541ca19221
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5311
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Add support for SWD debug to the Xilinx XVC/PCIe driver.
This is possible since the device is essentially a shift-register.
So doing SWD vs JTAG is a matter of wiring things correctly on the
RTL side (use TMS for SWDI, TDO for SWDO).
The clang static checker doesn't find any new problems with this change.
Change-Id: I3959e21440cd1036769e8e56a55e601d3e4aee9a
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5447
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.
Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
Identified by checkpatch script from Linux kernel v5.7-rc1 using
the command
find doc/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPO_SPELLING --strict -f {} \;
Change-Id: I1269ac966027439e16eb6e63179e43925bec37fa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5614
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Commit 87a4158acf ("drivers: xds110: Clean up command syntax and
documentation") does not follow the documentation structure that
lists the adapters in cpt 2 "Debug Adapter Hardware" then lists
the adapter commands in cpt 8.2 "Interface Drivers"; it puts all
in cpt 2.
While doing that, uses an incorrect texinfo syntax that causes the
following warnings at compile time:
doc/openocd.texi:543: warning: @deffn should only appear at the beginning of a line
doc/openocd.texi:547: warning: @deffn should only appear at the beginning of a line
doc/openocd.texi:552: warning: @deffn should only appear at the beginning of a line
Move the documentation of xds110 commands in the proper chapter
and fix the texinfo syntax.
Change-Id: I0b3f0fe0c687f194bb02e2d81aca86fcd4fdd718
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 87a4158acf ("drivers: xds110: Clean up command syntax and documentation")
Reviewed-on: http://openocd.zylin.com/5613
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Edward Fewell <efewell@ti.com>
Some flash banks are not mapped in the target memory
(e.g. SPI flash, some special pages).
Add flash version of mdw/h/b which reads data using
the flash driver.
Change-Id: I66910e0a69cf523fe5ca1ed6ce7b9e8e176aef4a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4776
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Changes since v1:
-Moved from http://openocd.zylin.com/#/c/5332/4
into separate commit.
28.02.2020:
-Removed multiple cpu configuration section, currently
only ARC EM is supported.
17.03.2020:
-Some cleanup
-For "arc set-reg-exists" command limitize the number of
arguments (50 maximum).
17.03.2020(v2):
-Revert limitation for "arc set-reg-exist" command
Change-Id: I4b06f89df95f2773bfde6e1bd2ae2b6b880bfaa8
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5351
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Events TARGET_EVENT_STEP_START and TARGET_EVENT_STEP_END
have been added - analogous to already existing events
TARGET_EVENT_RESUME_*.
This is an example of a concrete use case where having
these events is important:
In RISC-V processors without Debug Program Buffer, OpenOCD
cannot execute fence/fence.i when resuming or single-
stepping. With these events implemented, the user can
instead provide custom operations to achieve that same
effect prior to resuming the processor.
Change-Id: I786348ff08940759d99b0f24e9e0ed5a44581094
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5551
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
target types are sorted alphabetically
minor changes for some precision:
- cortex_a : it's an ARMv7-A core
- cortex_m : besides the ARMv7-M it support the v6-M and v8-M cores
Change-Id: I37ade2392fe3948fba4156a2831bbd8739fa9993
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5486
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Arrange all commands under a top level xds110 command. Fix
documentation to properly reflect the current functionality.
Also updated the links in the document to the new permanent
links for the XDS110 only support.
Patch updated for comments from code review. Return
ERROR_COMMAND_SYNTAX_ERROR for wrong number of args in
commands. Added deprecated commands to src/jtag/startup.tcl.
Change-Id: Ica45f65e1fdf7fa72866f4e28c4f6bce428d8ac9
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5495
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32WLEx devices are based on arm Cortex-M4 running at 48MHz,
contains a single bank of maximum 256 Kbytes of flash memory.
there is 3 variants with different Flash/RAM sizes:
STM32WLE5JC : 256K/64K
STM32WLE5JB : 128K/48K
STM32WLE5J8 : 64K/20K
the work-area size is set to 20 kb to fit in STM32WLE5J8
Change-Id: Ie8e186fe4be97cbc25c53ef0ade4b4dbbcee6f66
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5450
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash module of STM32G0/G4 family is quite similar to the one of
STM32L4, so only minor changes are required, in particular
adaption of flash loader to Cortex-M0. Register addresses
passed to flash loader to simplify integration of L5.
Added re-probe after option byte load.
Added flash size override via cfg file.
WRPxxR mask now based on max. number of pages instead of fixed 0xFF,
as G4 devices fill up unused bits with '1'.
Sizes in stm32l4_probe changed to multiples of 1kB.
Tested with Nucleo-G071RB, G030J6, Nucleo-G431RB and Nucleo-G474RE.
Gap handling in G4 Cat. 3 dual bank mode tested with STM32G473RB.
This handling isn't optimal as the bank size includes the
size of the gap. WB not tested.
Change-Id: I24df7c065afeb71c11c7e96de4aa9fdb91845593
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4807
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
A configuration script may want to check the reason why examine fails
e.g. device has security lock engaged.
tcl/target/kx.cfg and klx.cfg is modified to use the new event
for testing of the security lock of Kinetis MCU
Change-Id: Id1d3a79d24e84b513f4ea35586cd2ab0437ff9b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4289
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added fixes for issues found in additional code reviews.
Fixed host Endianness issues with using buffer reads
and writes instead of the *_u32 variants.
Changed code that tried to ID banks by hardcode
bank_number values to use instead the bank base
address. This fixes problems using configurations
with multiple devices.
Note that this replaces Change 4786 which has
been abandoned because of extensive changes to
the code to stop IDing banks by name. And I
think I really messed up a rebase/merge on the
document file.
Tested on MSP432P401R, MSP432P4111, and MSP432E401Y
Launchpads.
Change-Id: Id05798b3aa78ae5cbe725ee762a164d673ee5767
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5481
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Adopted only fast algorithm for flash programming:
- write_word and write_byte methods have been removed.
- start and end write alignments have been defined.
Moved flash controller registers offsets in a common file
shared with the flash algorithm.
- the flash base address is passed to the flash algorithm
as a parameter.
Removed unused functions
Change-Id: I80aeab3994e477044bbcf02e66d9525dae0cb491
Signed-off-by: luca vinci <luca.vinci@st.com>
Reviewed-on: http://openocd.zylin.com/5393
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Michele Sardo <msmttchr@gmail.com>
The default log output is stderr. After the command "log_output"
has been used to set an output log file, it is possible to return
back to stderr only on *NIX hosts specifying a new log output file
as "/dev/stderr", but this is not intuitive, not documented and
not portable out of *NIX.
Make command "log_output" able to set back the default output to
stderr when the parameter is either "default" or is missing.
While there, add debug message to log the change and make the
command return error on incorrect syntax.
Change-Id: I8c7c929780f58e2c23936737c8e7274a96734786
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5233
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is to avoid confusion with STM32 L4, L4+ and L5 families
also:
- a warning message is changed to error
- stm32l0x and stm32l1x aliases has been created to permit
the usage of either names
Change-Id: If3f16d2a3b7d1369959aa7407da37a9076ea91d7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5437
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
currently we have different types of same command group:
- starting with adapter_*
- starting with interface*
- without adapter or interface prefix.
Since interface name is already used, we can only use "adapter" command
group by keeping old commands as well.
Change-Id: Id0a1cb63a2ea6860c67ae1e7a3a06a37ddf464f4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4774
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for Xilinx Virtual Cable over PCIe JTAG controller.
It is commonly used in Xilinx based PCI Express designs with JTAG IP
in the FPGA fabric.
Access to the JTAG registers happens via the PCI Express extended
configuration space.
This can be used to debug soft-cores instantiated in the FPGA fabric.
The clang static checker doesn't find any new problems with this change.
Change-Id: Ib12ede0d1f26dacfda808d5e05b947b640c5bde7
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marex
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace the JTAG transport specific command with a more generic
one. Deprecate "jtag_reset" and update the documentation.
While there, fix an error in the documentation, where the command
"jtag_reset" was used in place of command "reset_config".
Change-Id: I41a988d37ce69f7b35a960cbaf5306aab0299b99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5286
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
these commands have been introduced to ease the manipulation of CTI trough
script files, these commands are:
- $cti_name ack $event : to acknowledge a CTI event
- $cti_name channel $channel_number $operation: to perform an operation
on a specific channel, the possible operations are:
gate, ungate, set, clear and pulse
Change-Id: I35463867a3c85072f3776c3aeb1e5788953ec435
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5315
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
functions managing option bytes cache (stm32x_read/write_options)
have bee removed, and a new functions to modify a single option byte
have been introduced (stm32x_write/modify_option).
by the way, some helpers have been introduced to access flash registers:
- stm32x_read_flash_reg(bank, offset, *value): int
- stm32x_write_flash_reg(bank, offset, value): int
and a new commands to read and write a single flash option register:
- stm32h7x option_read <bank> <option_reg offset>
- stm32h7x option_write <bank> <option_reg offset> <value> [mask]
also lock and unlock handlers' have been reduced by using the same routine
(stm32x_set_rdp) and have been optimized to not write options unless
there is a change in RDP level.
finally, several functions have been fixed to lock flash / options in case
of failure.
Change-Id: I75057949ab9f5b4e0f602bafb76f9f80d53a522b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5293
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
nrf5 flash driver detected devices by looking up the HWID in the table
of known devices. Unfortunately chips are produced with many different
HWIDs for each type.
All nRF52 devices have FICR INFO field suitable for device identification
without need of HWID lookup.
Some newer nRF51 devices have FICR INFO too although undocumented.
Use this information to identify the device.
nrf5_info() is reworked to show just concise info.
Decoding FICR and UICR registers was moved from nrf5_info()
to a new command 'nrf5 info' without functional changes.
The flash bank for UICR page has the same size as program flash sector.
Change-Id: I900095b9ae23ee995f8e2bef8539b75d00300da5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4848
Tested-by: jenkins
The preverify option allows to check whether flashing is necessary.
If the target is flashed often/automatically this can save time and
preserve the flash. This is expecially helpful in CI environments.
Change-Id: Iead0a269e1a772b751d4dd9e8b53b2fecc874624
Signed-off-by: Moritz 'Morty' Strübe <moritz.struebe@redheads.de>
Reviewed-on: http://openocd.zylin.com/5292
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
SWM050 is a series of MCU product by Foshan Synwit Tech, which is
available in TSSOP-8 or SSOP-16 packages.
Adds flash driver for the internal 8KiB flash of the MCU. The registers
are based on reverse engineering the J-Flash blob provided by the
vendor.
Also adds a pre-made cfg file.
Change-Id: I0b29f0c0d062883542ee743e0750a4c6b6609ebd
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-on: http://openocd.zylin.com/4927
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is causing repeated build failures. Its design is so fundamentally
broken that if someone actually wants to use it, a full rewrite is the
only option. So it's not even worth deprecating in the hope that someone
will notice and fix it, just get rid of it.
Change-Id: I513069919a3873bd69253110f7fb6f622ee7d061
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5243
Tested-by: jenkins
Reviewed-by: Jeffrey Booher-Kaeding <Jeff.Booher-Kaeding@arm.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Extra whitespace in file creating build errors with makeinfo.
Change-Id: Ib764850c1c8ff596d3c753eadd8e27f8c5982d20
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/5229
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The documentation added for commit b3d29cb544
was merged after the end of the eSi-RISC section rather than AARCH64.
This patch relocates this hunk to the correct location.
Change-Id: I46a2d24442556e9e8000b46a5e1af03b83de6d98
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/5181
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The commands prefixed with "ocd_" are removed.
Remove any reference in the documentation.
Change-Id: I27cebaa4752752ec8700757bf1c98b267c24f15b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5088
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Current code provides two independent implementations for the
memory read/write commands:
a) jim_target_md()/jim_target_mw() for the target specific
commands "<target> m[dw][bhw]"
b) handle_md_command()/handle_mw_command() for the current target
commands "m[dw][bhwd]"
The case a) misses the handling of doubleword and calls functions
command_print_sameline() with first parameter NULL because defined
as jim handler.
Remove the code in jim_target_md()/jim_target_mw() and use the
same code in b) for the target specific memory read/write.
This approach also provides support for 64-bit data size, not
present in the implementation in a).
The only drawback is that the implementation of memory read in b)
prints the data also as human readable ASCII characters, feature
missing in the implementation in a). This could introduced later
if it's really needed.
Update the documentation to:
- add 64-bit support
- add phys parameter
- add the count parameter
Add attribute "unused" to target_buffer_get_u8(), now not used
anymore.
Change-Id: Ib11ff924c409ad87e77fe708d628b2cc82b74d6a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5050
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit b04c7c2ca5 adds the cross
reference target "adapter_usb_location", but references it with
the command @xref inside a text, where command @ref should be
used. This triggers a compile warning:
doc/openocd.texi:2517: warning: `.' or `,' must follow @xref, not c
Replace @xref with @ref and adapt both the text and the command
syntax.
Change-Id: I1520ffecb7d1d375f924492b1884d5b47f399007
Fixes: b04c7c2ca5 ("ftdi: use "adapter usb location" instead of
ftdi_location command")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5045
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
`maskisr steponly` disables interrupts during single-stepping but
enables them during normal execution. This can be used as a partial
workaround for 702596 erratum in Cortex-M7 r0p1. See "Cortex-M7 (AT610)
and Cortex-M7 with FPU (AT611) Software Developer Errata Notice" from
ARM for further details.
Change-Id: I797a14e4d43f6dcb3706528ee4ab452846ebf133
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4673
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This can be used to dynamically distinguish between similar chips in tcl
code.
Change-Id: Ic4dfb61693e78616355173142dc7f9b9683a9f73
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5033
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In Texinfo, a comma inside an @url separates parameters to the @url
function rather than being included as part of a parameter. Use @comma{}
instead to resolve this.
Change-Id: I8b38939462cf4452e5bc2582ee484220aaf83ae0
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5028
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Seams over-engineered having two separate commands to turn SMP
on/off. Plus it is missing the possibility to dump the current
status of SMP and would be weird adding an additional command
for it. Moreover, such commands are replicated in few targets so
it would make sense centralizing them.
- Deprecate the commands "smp_on" and "smp_off".
- Add a new command "smp" that accepts optional parameters
"[on|off]" and prints the SMP status when run without
parameters. This replaces the two commands above.
- Put the deprecated and the new command handlers in smp.c
- Update the documentation, except for mips_m4k, since it is not
available yet.
- Promote the macro foreach_smp_target to global context and use
it where possible.
Change-Id: Ia72841c1a3bd6edd4db4cc809046322f498617e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4615
Tested-by: jenkins
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This represents months of continuing RISC-V work, with too many changes
to list individually. Some improvements:
* Fixed memory leaks.
* Better handling of dbus timeouts.
* Add `riscv expose_custom` command.
* Somewhat deal with cache coherency.
* Deal with more timeouts during block memory accesses.
* Basic debug compliance test.
* Tell gdb which watchpoint hit.
* SMP support for use with -rtos hwthread
* Add `riscv set_ir`
Change-Id: Ica507ee2a57eaf51b578ab1d9b7de71512fdf47f
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4922
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds "hwthread", a pseudo rtos that represents cpu cores
in an SMP system as threads to gdb. This allows to debug SMP
system kernels in a more sensible manner and removes the current
atrocities of switching gdb manually between CPU cores to update
the context.
Change-Id: Ib781c6c34097689d21d9e02011e4d74a4a742379
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3999
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
add command 'catch_exc' to halt a core on entering any of Secure EL1 or
EL3 or Non-Secure EL1 or EL2.
Change-Id: I0c68e247af68dd96616855a9bc1063c277d222e5
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4479
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The OTP is part of the flash memory. It has 512 (1024 for F7) bytes
and is organized in 16 sectors with 32 (64 for F7) bytes each.
The OTP is exposed as separate flash bank 1 and can be used
with the usual flash commands.
Writing the OTP can be done as follows:
> stm32f2x otp 1 enable
> flash write bank 1 foo.bin 0
> mdw 0x1fff7800 4
> verify_image foo.bin 0x1fff7800
> stm32f2x otp 1 disable
Note: This patch is largely a rebase/cleanup of a patch
from 2012 by Laurent Charpentier and he did most of the work.
No new Clang-Analyzer warnings.
Change-Id: I5e6371f6a7c7a9929c1d7907d6ba4724f9d20d97
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/829
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Xref without trailing '.' or ',' was introduced in
deaf3d2641
Change-Id: I99afd40e1ffeddd1298b7b07e4deba3dcc41799f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4905
Tested-by: jenkins
Adds ability to change the user data in STM32F1x/STM32F3x MCU's option byte.
Since OpenOCD prints the content of user data in option byte registers, it
is seems logical to also provide a way how to change this data.
Change-Id: Ie6cb756b4f11b5c6dabd34bc89434a358eb758ff
Signed-off-by: Jan Vojtech <honza.vojtech@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4663
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The new Microchip (former Atmel) series powered by Cortex-M4 looks
very similar to older M0+ powered SAM D2x at the first sight.
Unfortunately the new series differs a lot in important details.
NVMCTRL has different register addresses, moved important bits
and even changed binary command set. An universal driver for all SAM D/E
would be very complicated. That's why a new driver was derived.
Tested on Microchip SAM E54 Xplained Pro kit (board cfg included).
Adjusted for the restructured dap support.
Checked by valgrind and clang static analyzer.
Change-Id: I26c67047a552076f4b207b9b89285a53d69b4ca4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4272
Tested-by: jenkins
Reviewed-by: Andres Vahter <andres.vahter@gmail.com>
Valgrind and Clang Static Analyzer have no complaints about this change.
Change-Id: I7757615ec52448372bdc57729cdf97c7016d97e8
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4656
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The XDS110 stand-alone version has the ability to supply
voltage to the target board via it's AUX FUNCTIONS port.
Added command to enable setting the voltage on the XDS110
stand-alone.
Change-Id: I2f21c4a3d15ed99e649f3a83973c5e724c4bfeb6
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4793
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These devices differ from LPC8xx devices in that they have a different
IAP entry point, but everything else is the same. Using Tcl to pass
different IAP entry point.
no new Clang analyser warnings and no new build sanitizers issues.
Change-Id: I2d654dd250f416e74262c0228cad8713a283402f
Signed-off-by: Rod Boyce <developer@teamboyce.co.uk>
Reviewed-on: http://openocd.zylin.com/4684
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently it is impossible to flash ELF with correct offsets. The reason
is a bogus offset calculation extracted from base.
Since any other spi drivers do not care about base, do the same for
ath79 as well.
Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4821
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
w600 is a wifi soc from winner micro(www.winnermicro.com).
Change-Id: Ib8ccd6e52baefca6547fb97d29db75db0ee73948
Signed-off-by: Simon Qian <versaloon@simonqian.com>
Reviewed-on: http://openocd.zylin.com/4801
Tested-by: jenkins
Reviewed-by: yichen <wdyichen@wdyichen.cn>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove option 'srst' which is not recognized from on-line help and texi.
Check parameter and return syntax error if wrong option is entered.
Change-Id: I87daa423a9f53193a0b015080594820b933628f5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4795
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Cortex-M0, M0+ and M1 do not support VECTRESET bit in AIRCR.
Without this change the 'reset' command silently fails if VECTRESET
is requested.
Detect these cores, show warning if VECTRESET is about to use
and use SYSRESETREQ instead.
Change-Id: Ief174373e3ef0e6b287c57911c0aca4dfa8209f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4794
Tested-by: jenkins
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for instruction tracing to eSi-RISC targets. The
command interface is borrowed heavily from ETM; eSi-Trace uses a less
sophisticated model for tracing, however the setup and usage is similar.
This patch also cleans up the command interfaces of the other esirisc
command groups and adds additional debugging information to log messages
when dealing with CSRs.
This patch "finalizes" support for 32-bit eSi-RISC targets.
Change-Id: Ia2a9de79a3c7c066240b5212721fb1b7584a9a45
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4780
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added fixes found in additional code reviews.
Remove inappropriate use of bank_number field and updated
documentation to reflect the change.
Restored functionality to cc2538.cfg file because previous
change removed the cc26xx.cfg file because the flash support
changes made it obsolete. Rolled the previous cc26xx.cfg
file into cc2538.cfg and updated it to work with other
recent changes. Tested using a SmartRF06 Evaluation
board with embedded XDS100v3 and external XDs110.
Change-Id: Ia19d00cf8055c5c0f1acc53aa23fd06a80fd2ebc
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4787
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Extend the driver to include the minimal functionality to support
the HLA model.
Due to the small change in the name (ST-LINK/V2 => STLINK-V3), fix
the existing names in the comments in udev rules.
Change-Id: Ied33e38063a6da81d9bf249ed195444d7cdf4f03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4717
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
FT232R: introducing configurable parameters for pinout,
initial buffer size, state of RS232 signals at exit with
option to reattach kernel driver. All this was hardcoded before.
New parameters are documented in "openocd.texi" file.
Allows hopfully self-explainable and user-friendly adaptation to
various pinouts and similar chips like FT230X and FT231X.
Change-Id: Ib807f2ea3d4c1a164d351d65aeacd1978318d217
Signed-off-by: EMARD <vordah@gmail.com>
Reviewed-on: http://openocd.zylin.com/4681
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Handle write protection status in blocks instead of sectors, removing
unnecessary complexity in the process. Now closer to stm32f2x.
Support sequential modification of option bytes by read/modify/write
directly to option bytes area instead of always starting with the
currently loaded bytes from FLASH_OBR/WRPR registers.
Added new command 'options_load' to force re-load of option bytes w/o
having to power cycle target.
Change-Id: I5c76191e29c17a1e11482df06379d10ca8d6d04d
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4576
Tested-by: jenkins
Reviewed-by: Jan Vojtěch <honza.vojtech@gmail.com>
eSi-RISC is a highly configurable microprocessor architecture for
embedded systems provided by EnSilica. This patch adds support for
32-bit targets and also includes an internal flash driver and
uC/OS-III RTOS support. This is a non-traditional target and required
a number of additional changes to support non-linear register numbers
and the 'p' packet in RTOS support for proper integration into
EnSilica's GDB port.
Change-Id: I59d5c40b3bb2ace1b1a01b2538bfab211adf113f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4660
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Enables the programming of Write protection lock bits.
- Updated/re-factored with option_read, option_write and option_load commands.
Change-Id: I86358c7eb1285c3c0baac1564e46da8ced5fd025
Signed-off-by: Thomas Søhus <tls@ceepro.dk>
Reviewed-on: http://openocd.zylin.com/4654
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 31c58c139d ("jtag: drivers: stlink: handle all versions with
single config") deprecates the use of "interface/stlink-v2-1.cfg" in
favor of a unique config file "interface/stlink.cfg".
Update the example in the documentation.
Change-Id: I1aed7c70e15f4edb4f81a3ee8e3bce575fde873b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4667
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Antonio Borneo
Tarek BOCHKATI
Yasushi SHOJI
Paul Fertser
Jonathan McDowell
Marc Schink
Tomas Vanek
Andreas Bolsch
Tim Newsome
Andreas Fritiofson
Kevin Burke
Mete Balci
Zale Yu
Daniel Krebs
Moritz Fischer
Evgeniy Didin
Jan Matyas
Marc Schink
Edward Fewell
luca vinci
Oleksij Rempel
Moritz 'Morty' Strübe
Caleb Szalacinski
Kevin Gillespie
Steven Stallion
Christopher Head
Leonard Crestez
Matthias Welwarsky
Moritz Fischer
Jan Vojtech
Rod Boyce
Oleksij Rempel
Jean-Christian de Rivaz
Simon Qian
Spencer Oliver
EMARD
Dominik Peklo
Thomas Søhus