Gets rid of the runtime warning "stm32.bs: nonstandard IR mask"
[dbrownell@users.sourceforge.net: line lengths, note issue, section ref]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This gets rid of runtime warnings from the use of numbers.
STM32 and LPC2103 were tested. Other LPC updates are the
same, and so are safe. The CFI updates match other tested
changes now in the tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Now I can issue "reset halt" and have everything act smoothly;
the vector_catch hardware is obviously not kicking in, but the
rest of the reset sequence acts sanely.
- TAP "setup" event enables the DAP, not omap3_dbginit
(resolving a chicken/egg bug I noted a while back)
- Remove stuff from omap3_dbginit which should never be
used in event handlers
- Cope better with slow clocking during reset
Also, stop hard-wiring the target name: use the input params in
the standard way, and set up $_TARGETNAME as an output param.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Startup now mostly works, except that the initial target state
is "unknown" ... previously, it refused to even start.
Getting that far required fixing the ircapture value (which
can never have been correct!) and the default JTAG clock rate,
then providing custom reset script.
The "reset" command is still iffy. DCSR updates, and loading
the debug handler, report numerous DR/IR capture failures.
But once that's done, "poll" reports that the CPU is halted
(which it shouldn't be, this was "reset run"!), due to the
rather curious reason "target-not-halted".
Summary: you still can't debug these parts, but it's closer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Without some extra delay after releasing SRST, we seemed to
be trying to talk to the TAP before it was ready to respond.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The model is that this fires after scanchain verification, when it's
safe to call "jtag tapenable $TAPNAME". So it will fire as part of
non-error paths of "init" and "reset" command processing. However it
will *NOT* trigger during "jtag_reset" processing, which skips all
scan chain verification, or after verification errors.
ALSO:
- switch DaVinci chips to use this new mechanism
- log TAP activation/deactivation, since their IDCODEs aren't verified
- unify "enum jtag_event" scripted event notifications
- remove duplicative JTAG_TAP_EVENT_POST_RESET
git-svn-id: svn://svn.berlios.de/openocd/trunk@2800 b42882b7-edfa-0310-969c-e2dbd0fdcd60
It can be sped up later, once it's known the PLLs are active.
Note that modern tools from TI all use adaptive clocking; and
that if that's done with OpenOCD, "too fast" is also a non-issue.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2740 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update the board config for the DaVinci DM355 EVM so the reset-init
event handler does the rest of the work it should do:
- minor PLL setup bugfixes
- initialize the DDR2 controller
- probe both NAND banks
- initialize UART0
- enable the icache
git-svn-id: svn://svn.berlios.de/openocd/trunk@2699 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- remove endianness options; these chips hard-wire "little"
- $_TARGETNAME updates:
* don't pass $_TARGETNAME where a TAP label is required
* flash config uses $_TARGETNAME (it might not be target #0)
* simplify one $_TARGETNAME construction
- update work area setup:
* remove VM spec; these chips have no VM!
* fix some wrong sizes (0x4000 == 16K, not 4K)
* simplify: take defaults
- comment fixups
git-svn-id: svn://svn.berlios.de/openocd/trunk@2589 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add flash programming support for NXP LPC1700 cortex_m3 based family
git-svn-id: svn://svn.berlios.de/openocd/trunk@2579 b42882b7-edfa-0310-969c-e2dbd0fdcd60
