The use of 'void *' makes the pointer arithmetic incompatible with
standard C, even if this is allowed by GCC extensions.
The use of 'void *' can also hide incorrect pointer assignments.
Switch to 'uint8_t *' and add GCC warning flag to track any use of
pointer arithmetic extension.
Change-Id: Ic4d15a232834cd6b374330f70e2473a359b1607f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5937
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit 80f1a92bd7 ("mips64: Add generic mips64 target support")
adds a log of the target's program counter in function
mips_mips64_debug_entry() by directly casting the little-endian
buffer in pc->value.
This is going to print an incorrect value on big-endian hosts.
Use the function buf_get_u64() to return the register value.
Not tested on real HW. Issue identified with GCC compiler flag
'-Wcast-align=strict' after change http://openocd.zylin.com/5937/
("target/register: use an array of uint8_t for register's value").
Change-Id: Icbda2b54a03fdec287c804e623f5db4252f9cd2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 80f1a92bd7 ("mips64: Add generic mips64 target support")
Reviewed-on: http://openocd.zylin.com/5944
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The original code passes to ->read_core_regs() and to
->read_xpsr() the pointer to the little-endian buffer reg.value.
This is incorrect because the two functions above require a
pointer to uint32_t, since they already run the conversion with
arm_le_to_h_u32() in the jtag callback.
This causes a mismatch on big-endian host and the registers get
read with the incorrect endianness.
Use an intermediate buffer to read the registers as uint32_t and
to track the destination reg.value pointer, then copy the value in
reg.value after the call to jtag_execute_queue().
Tested with qemu-armeb and an OpenOCD built through buildroot
configured for cortex-a7 big-endian.
Note that if jtag_execute_queue() fails, the openocd register
cache is not updated, so the already modified flags 'valid' and
'dirty' are incorrect. This part should be moved after the call to
jtag_execute_queue() too.
Change-Id: Iba70d964ffbb74bf0860bfd9d299f218e3bc65bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5943
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit fc2abe63fd ("armv7m: use generic arm::core_mode") adds
two special modes for ARMv6M and ARMv7M in struct arm_mode_data[].
While these modes do not have any additional register to be dumped
by command 'arm reg', the command still prints an header for these
modes but not followed by any register.
Detect the special modes for ARMv6M and ARMv7M and skip them to
avoid printing the useless header.
Change-Id: I04145769e5742624f143c910eebf9a6f6d8e3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fc2abe63fd ("armv7m: use generic arm::core_mode")
Reviewed-on: http://openocd.zylin.com/5942
Tested-by: jenkins
Commit fed7131049 ("armv4_5: support weirdo ARMv6 secure monitor
mode") introduces the secure mode 28 of ARMv6 as a synonymous of
mode 22 (MON), but does not add it in the switch/case in command
'arm reg'.
When command 'arm reg' scans the array arm_mode_data[] on targets
without secure modes, it does not detect the new secure mode as
not supported by the architecture, thus triggers a segmentation
fault when it try to read the register's value from unallocated
memory.
Issue detected with target arm926ejs.
Add the new mode in the switch/case and treat it as the mode MON.
Change-Id: I2b72cc558e097879a7ee6ea601200bfda6b60270
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fed7131049 ("armv4_5: support weirdo ARMv6 secure monitor mode")
Reviewed-on: http://openocd.zylin.com/5941
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
From JEP106AZ, released on May 24, 2019.
Change-Id: I768b7077ec6abcd19ae1530b5715c7ea993add67
Signed-off-by: Boran Car <boran.car@hex-five.com>
Reviewed-on: http://openocd.zylin.com/5244
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Real Time Transfer (RTT) is an interface specified by SEGGER based on
basic memory reads and writes to transfer data bidirectionally between
target and host.
Every target that supports so called "background memory access", which
means that the target memory can be accessed by the debugger while the
target is running, can be used.
RTT is especially of interest for targets which do not support Serial
Wire Output (SWO) (e.g. ARM Cortex-M0) or where using semihosting is
not possible (e.g. real-time applications) [1].
The data transfer is organized in channels where each channel consists
of an up- and/or down-channel. See [2] for more details.
Channels are exposed via TCP connections. One or more RTT server can be
assigned to each channel to make them accessible to an unlimited number
of TCP connections.
The current implementation does not respect buffer flags which are used
to determine what happens when writing to a full buffer.
Note that the implementation is designed in a way that the RTT
operations can be directly performed by an adapter (e.g. J-Link).
[1] https://devzone.nordicsemi.com/tutorials/6/
[2] https://www.segger.com/jlink-rtt.html
Change-Id: I8bc8a1b381fb74e08b8752d5cf53804cc573c1e0
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4055
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reading of DPIDR is the very first operation after JTAG to SWD sequence.
Without this change if DPIDR read fails then swd connect fails.
Keep trying JTAG to SWD sequence and DPIDR read until success
or timeout 0.5 sec. It makes setting of adapter srst delay on SWD transport
mostly unnecessary.
Also test for ERROR_WAIT (which should not occur according to
IHI 0031E B4.3.2 but a quirk is known) and if bus is kept stalled
then issue abort to make the next connect possible.
Change-Id: Id8fe6618605bbeb4fed5061e987ed55de90a35f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5730
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If dap_dp_read_atomic() in 30 trials loop fails, dap->do_reconnect is set.
Following dap_dp_read_atomic() calls dap_queue_dp_read() which in case
of SWD transport calls swd_queue_dp_read(). It starts
with swd_check_reconnect() and it calls swd_connect() because
dap->do_reconnect is set. swd_connect() does some initialization,
reads DPIDR and calls dap_dp_init() again!
Moreover if dap_dp_init() is called from cortex_m_reset_(de)assert()
one level of recursion is necessary to reconnect the target.
Introduce dap_dp_init_or_reconnect() for use in cortex_m reset
and similar.
Remove loop of 30 atomic reads of DP_STAT to prevent unwanted recursion.
Change-Id: I54052fdefe50bf5f7c7b59fe751fe2063d5710c9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5729
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Every debug log of OpenOCD contains approximately 130 lines like:
Debug: 264 147 command.c:354 register_command_handler(): registering 'flash'...
Because only root name of the command is logged, most of lines is not
too informative. E.g. registering 'flash' is repeated 14 times.
Karl Passon submitted the patch [1] changing the logged cmd name from
root to lowest level. It makes the log better. Unfortunately we also have
'reset_config' and 'cortex_m reset_config' and similar which looks
equal in the log after [1].
Moreover [1] has not been reviewed for 5 years.
So my guess is that nobody uses that crap in debug log.
Save more than 10 kbytes in any debug log and make log analyse easier
by blocking log command in #if 0 block.
If some developer eventually needs to debug cmd registering he can easily
enable logging again.
[1] http://openocd.zylin.com/2765
Change-Id: Ib7e528aadd692fd0da2e3c005b4c5a484551b728
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5928
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
flash_regs table is introduced within stm32l4_flash_bank struct in order
to get correct register offsets, by using the driver internal function
'stm32l4_get_flash_reg_by_index'.
To use efficiently register indexes, stm32l4 _[get|read|write]_flash_reg
functions are surcharged to accept register indexes.
IMPORTANT: stm32l4_write_option is not surcharged, and they always accept
the option register offset.
tested on NUCLEO-G474RE and STM32L4R9I-DISCO
Change-Id: I739d3e97d63b831af6aa569c5629db0000209551
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5509
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Avoid multiple definition of cmsis_dap_usb_backend and
cmsis_dap_hid_backend using 'extern'.
Move the prototypes in cmsis_dap.h.
Remove the useless #if/#endif around the prototypes.
Change-Id: I8d73fe148e2155620244bc887d4235e9af530e30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5790
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
http://openocd.zylin.com/4831 has following problems in selecting
USB device/interface to connect:
- attempts connection to any device with user class and 2 bulk endpoints
- regardless of cmsis_dap_vid_pid or cmsis_dap_serial setting
connects to the first suitable device
Distinguish between real match and no filtering cases and use that info
appropriately.
Add debug messages to show why the interface is refused.
Move CMSIS-DAP interface string detection before checking of class/endpoints
to give more understandable debug log in the case the device is refused.
Keep track of reliable matches in both device and interface enumeration.
First search for the interface with CMSIS-DAP in the interface string.
If it fails, chose the first suitable interface.
Change-Id: Ia1aacd5631a9f5c5db580bfb5745ceb6240d61ad
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5789
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This change implements CMSIS-DAP v2 which works with raw USB bulk transfers.
The old driver is now split into a generic CMSIS part and a HID backend,
with a new raw USB backend for CMSIS-DAP v2.
New commands:
- cmsis_dap_backend (usb_bulk | hid | auto)
- cmsis_dap_usb interface <interface number>
Change-Id: I4218477b12ccbfe19c9b332321cd21394bf44e30
Signed-off-by: Mickaël Thomas <mickael9@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4831
Tested-by: jenkins
Change-Id: I4fea29f07f4d3b8b2578b538ef0eef5f1eea285f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5876
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
PSoC6 erases flash to 0x00 not more common 0xff, so a device
with erased flash loads xPSR.T=0 from the zeroed reset vector.
Wrong thumb bit value caused a target algorithm failed with HardFault.
The low level write to xPSR solved the problem only if xPSR cached
copy was not marked dirty.
Later commit 49bd64347a fixed T setting
for all Cortex-M target algorithms.
Since 49bd64 this part of code is useless as xPSR target_start_algorithm()
sets always xPSR dirty so the effect of the low level write is eliminated
(and proper setting of thumb bit is ensured in target_start_algorithm())
Change-Id: I68aea5e921fbc6203f2fe91a45f10d22869327de
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5875
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a Cortex-M (not M0, M0+) target was stopped in the middle of
a conditional IT block or in the load/store multiple instruction,
cortex_m_debug_entry() used wrong xPSR bits to detect it and then
cleared 8 bits of the exception number from xPSR
- probably wrong bit mask again.
I believe clearing of the ICI/IT bits in cortex_m_debug_entry() has no
reason as Cortex-M does not use instruction injecting.
Remove the wrong code.
The change was originally a part of http://openocd.zylin.com/4862
It is now re-submitted as #4862 is not ready.
Change-Id: If91cd91d1b81b2684f7d5f10cf20452cde1a7f56
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5874
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Register xPSR is indexed directly with its value 16 or with the
incorrect enum ARMV7M_xPSR.
Replace them with the new enum ARMV7M_REGSEL_xPSR.
Change-Id: I86600e7f78e39002ce45f66d4792d5067c1f541b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5873
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Old stlink firmware in stlink V1 and stlink V2 pre-J15 do not
handle FPU registers in the read_reg() and write_reg() API.
Add code to be compatible with the new API of OpenOCD.
Change-Id: Ib0439c5294b6911ea75efe8c7fa085b014317a4b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5883
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The API of hla have been defined from ST-Link basic operations.
By chance, all the current implementation of hla (st-link, ti-icdi
and nulink) share the same way to handle the parameter 'num' of
the API read_reg() and write_reg(), that is simply using it to
initialize the field REGSEL (bits [6:0]) of armv7m Debug Core
Register Selector Register (DCRSR).
Add a comment in the API definition to highlight this, in case it
get used by a further hla implementation, then rename as 'regsel'
the 'num' parameter.
Change-Id: I4b6a2c7d78b4fc4de2b9b2bdba065414b15c6ba3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5882
Reviewed-by: Edward Fewell <edwardfewell@hotmail.com>
Tested-by: jenkins
Reviewed-by: Zale Yu
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Consolidate low level register read/write.
Floating point registers were handled by target_read/write_u32
unlike other registers handled by cortexm_dap_read/write_coreregister_u32
There is no reason to do so in cortex_m.
Remove cortexm_dap_read/write_coreregister_u32
and use cortex_m_load/store_core_reg_u32 directly.
Similarly HLA adapters register read/write interface supports all registers
so use it for any floating point and other registers.
Change-Id: Ida679e5f4fec02d94ffb0bd3f265ed7ed2221cdc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5864
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Move primask/basepri/faultmask/control packing/unpacking from
cortex_m.c and hla_target.c to armv7m.c armv7m_read_core_reg()
and armv7m_write_core_reg() where also the FP 32/64-bit registers
conversion takes place.
Introduce a new hidden register ARMV7M_PMSK_BPRI_FLTMSK_CTRL
for packing/unpacking of special registers in the register cache.
The new packing/unpacking is endianess safe.
While on it improve returned error codes and LOG_ messages.
Just minimal changes in cortex_m.c and hla_target.c, will be
consolidated in the next patch.
Change-Id: Id51e764e243e54b5fdaadf2a202eee7c4bc729fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5863
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Make arm register id coherent with reg_list index.
Without this reg_list[ARMV7M_R12] was possible but
reg_list[ARMV7M_FPSCR] was out of bounds.
Remove unused items from reg_list index.
Change-Id: I84d3b5c496fc1839d07a5b74cb1fd1c3d4ff8989
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5862
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Define a new enum with DCRSR.REGSEL selectors.
Introduce armv7m_map_id_to_regsel() to unify mapping in one place.
Use DCRSR.REGSEL selectors for low level register read/write.
Change-Id: Ida0ccdfa9cdb1257a1900b8bfbf172b076374d39
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Introduce a 'hidden' flag in struct reg to support a register cache
containing different views of same data: e.g. Cortex-M has
primask, basepri, faultmask and control registers accessed
as one word. With the hidden flag we can add an reg_list item
corresponding to hw access without exposing the register to user level.
All the struct reg are allocated with calloc() but one in xscale.c
allocated by malloc(). Change this one to use calloc() as well
to guarantee initial value hidden=false
Change-Id: I8da9f5a5a60777ae7ef943a841307487bd80fc6f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5325
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add space around operators;
use BIT() macro in place of left shifting constant 1;
remove space between cast operator and value;
do not check a pointer before free() it;
add parenthesis around parameters in macros;
fix indentation using only TABs;
remove line continuation '\' at code lines out of macros.
Change-Id: I809e8ee72d7bfe49d0edf10afb36efe2458de77c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5932
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
When the core is in sleep mode, the core is no longer retiring
instructions. Cortext M remains in "unknown" state. This patch converts
sleep mode to "running" state.
Change-Id: I1e9b6c9be51fd0f1f6ce81af9b1f5f9f1f43c661
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5921
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
Use integer rounding for the computation of prescaler.
Improve the test of prescaler range, knowing its value would be
decremented before being written in TPIU ACPR.
Change-Id: I041dde1dca41323904e36a6b6975028a6de902b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5909
Tested-by: jenkins
While stlink v2 anly accept till to 2 MHz for SWV baudrate, stlink
v3 accepts up to 24 MHz.
Check the stlink version and use the respective max value.
Change-Id: I911207a35983b6acf0b901059076dd31f70e6290
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Pawel <phryniszak@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/283/
Reviewed-on: http://openocd.zylin.com/5908
Tested-by: jenkins
The value stored in TPIU ACPR is the prescaler value decremented
by one. Thus, the test should verify that prescaler does not
exceed the maximum ACPR value plus one. Also, zero value is not
allowed for prescaler.
Change-Id: I1817f04f2a310b2f413bad726f0cb9dd6a4172e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5907
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Commit 462c012066 ("Add complete JTAG debug logging.") breaks
the build for minidriver, that is enabled either on zy1000 build
and on minidriver-dummy build. The check on BUILD_ZY1000 was added
to pass the auto-build in jenkins. While the build issue with
minidriver-dummy was known, as reported in the comment, it was not
addressed and got ignored for slightly more than one year.
Use the macro HAVE_JTAG_MINIDRIVER_H in place of BUILD_ZY1000 to
take in account both builds that require the minidriver.
Fix also the build in case configure enables the HLA drivers due
to autodetection of libusb. The HLA drivers would not be in the
build and the function transport_is_hla() would be missing.
Change-Id: I1d85c5fa247bf4a85aba29b233c0b573b46665bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5911
Tested-by: jenkins
The function arm7tdmi_clock_out() has one unused 'deprecated'
parameter.
Drop the unused 'deprecated' parameter and the FIXME above it.
Change-Id: Ia8de41f5b8258825faccc737bba622e44c81a7ea
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5912
Tested-by: jenkins
When a target examination fails, continue to examine subsequent targets.
Return the number of targets that failed to examine.
Change-Id: I883a0c445edc7eb00f496b79271d773771ec6b66
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When trace capturing the trace is enabled using 'tpiu_config internal'
(via the internal mode), OpenOCD can collect the trace buffers then append
it to a specified file or named pipe and propagate the trace to 'tcl_trace'
command.
This change is allowing OpenOCD to stream the captured trace over TCP.
When using this configuration OpenOCD acts like a server and multiple
clients can connect and receive the captured trace.
Example on STM32F7 running at 216MHz:
itm port 0 on
tpiu config internal :3344 uart off 216000000
Change-Id: Idea43e7e26e87b98a33da7fb9acf7ea50fe3b345
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5345
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
returning the created service seems useful:
as the only method to get the freshly created service is by getting the
last item in the services linked list, and this seems to be like an
intrusion to service internal mechanism.
possibly, we could get the service from a connection but this is possible
only from [new_connection|input|connection_closed]_handler_t, but this is
not always practical:
example: armv7m: add a TCP channel to stream captured trace
http://openocd.zylin.com/#/c/5345/
here we poll for trace and broadcast to all connections
outside of these xxx_handler_t functions
also, storing one of the connections in new_connection_handler_t and get
the service from it is possible, but this will make the code less readable.
Change-Id: I5fef1baecec1e054953c6faf5b99d864ecc97f02
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5717
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The function setup_command_handler() was used in the eCos build of
OpenOCD, thus it was exported and a comment was added to remark it
should remain not-static. Unfortunately the comment was missing
the relevant information of the special build that requires so.
Also unusual is that there is no include file that declares the
prototype of the function.
The comment above the function was added in two steps, in commit
ea3e49f4e2 ("fix embedded builds") and commit fb96b8607a
("openocd: setup_command_handler() must not be static"), again
without info about the special build.
Also the mailing list archive does not report any further detail.
The only hint is in the first commit above that also adds a test
on BUILD_ECOSBOARD in a #if.
Commit 39650e2273 ("ecosboard: delete bit-rotted eCos code")
removes all the eCos code, that effectively includes the both the
prototype and the call to the function setup_command_handler(),
http://openocd.zylin.com/#/c/503/2/src/ecosboard.c@a1092
but did not reverted the function to static.
With all the 'external' uses of this function being dropped, set
the function setup_command_handler() to static and remove the
obsoleted and misleading comment.
Change-Id: I4d6b83dec2a838119821189fc67949bfca070035
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions that are not used outside the file should be declared as
static.
Change-Id: Ie81f6bdce91e2a1456364b47f30aa4d35c7ee7bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5900
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
The function rtos_try_next() is only used internally.
Make it private.
Change-Id: I68c6b8d8e6bbf3d674b0e0199e63bc02d358c04e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5899
Tested-by: jenkins
The only use of this function has been removed with commit
159f11fefc ("jtag: set default "jtag_only" to uninitialized
transports").
Get rid of the unused function.
Change-Id: I79dd1d55bd54ed8edc39ed3443e6c3c01794f063
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5898
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions that are not used outside the file should be declared as
static.
Change-Id: I57b2fa6e49e87e14604bd34c4f1d2f037f401507
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5897
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I58c9f5557d4809db9ccc34d32182c3797f825da1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5896
Tested-by: jenkins
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I9f97571a528f0cb3c3c26f873577ab16fdec3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I9731a35496cd1c7421563c8961da5fa0e3cc71c3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5894
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I52d46ed6d4c9b98a7152eb23274c836416f409a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The new libftdi 1.5 (2020-07-07) changes some API, deprecating the
old ones. This cause a warning at compile time.
Detect in configure the version of libftdi.
Use the new API in the driver's code.
Add an helper include file 'libftdi_helper.h' that wraps the old
API for backward compatibility with old libftdi.
Change-Id: I7800fbebe17dd0ce62e55b3598d8c08be8875bb7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/286/
Reviewed-on: http://openocd.zylin.com/5891
Tested-by: jenkins
Is it possible to run OpenOCD without any target, for example to
only dump the rom-tables of an arm dap, or to perform low level
jtag operations.
But without any target created, the command 'target current'
causes OpenOCD to abruptly exit.
Handle in command 'target current' the case of no targets.
Change-Id: Ide15cb13bec84b88ccc3e7126523c04a6d70e636
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5881
Tested-by: jenkins
The default way of working is to have a single GDB attached to one
target, so OpenOCD accepts only one connection to the GDB port of
each targets and rejects any further connection.
There are some barely safe use cases in which it could get useful
having a second GDB connection to the same target.
One such use case is while using GDB as a 'non-intrusive memory
inspector', as explained in the OpenOCD documentation.
One GDB can be left running an infinite loop to dump some memory
area, or even analysing the content, while keeping a second GDB
ready for user interaction or spot memory check.
Add a target configure option to specify the maximum number of GDB
connections allowed for that target, keeping the default to 1.
Change-Id: I4985a602e61588df0b527d2f2aa5b955c93e125e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5865
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
To avoid code duplication, reorganize the code to replace
cti_configure() with adiv5_jim_mem_ap_spot_configure().
Reorganize 'struct arm_cti_object' and its sub-'struct arm_cti'
moving DAP and mem-AP info in a 'struct adiv5_mem_ap_spot'.
Replace cti_configure() with adiv5_jim_mem_ap_spot_configure().
Deprecate the use of '-ctibase' in favor of '-baseaddr'.
Change-Id: I43740a37c80de67c0f5e4dc79c3400b91a12e9e8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5869
Tested-by: jenkins
This is somehow an extension of existing adiv5_jim_configure(),
but includes the 'address' in the mem_ap.
Rewrite adiv5_jim_configure() using the new helper.
Change-Id: Ia7effeeece044004d459b45126ed4961a98b8568
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5857
Tested-by: jenkins
Clang static analyzer reported:
Warning: line 196, column 3
Potential leak of memory pointed to by 'fields'
Free allocated memory pointed by 'fields' and fields[i].in_value
Change-Id: I0b3935d9a235544afc03e39a4648319047e65815
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5906
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Warning: line 373, column 15
Assigned value is garbage or undefined
Most probably a false warning, building the hex string byte
per byte seems too complicated for static analyze.
Change malloc to calloc to silence the warning.
Change-Id: I746d43fa51abf05582ccf2680ed72dc557798a7a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5905
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Warning: line 955, column 3
Argument to free() is the address of a global variable, which
is not memory allocated by malloc()
It is definitely a false alarm. Simplify concatenation of arguments
and allocate a string always to silence the warning.
Change-Id: I5ac4cc610fc35224df0b16ef4f7102700363249f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5904
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Warning: line 679, column 4
4th function call argument is an uninitialized value
Change-Id: If62d96e1595be945c8e17885bb402e820fb1ec7b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5903
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
The xlnx_pcie_xvc_execute_stableclocks() function can and
should be static.
Change-Id: I45fb1363caee1f1762b0b1ac2c6bc1bb0153b15b
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5889
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The config_trace function has an out-parameter for generating the
prescaler for the TPIU. The STLink implementation wasn't always writing
it, causing the tpiu command to load uninitialized stack memory (minus
one) into the TPIU's prescaler register when 'external' was requested.
This change ensures that the out-parameter (and the other one,
trace_freq, which hadn't caused any buggy behavior for me) are written
every time.
Signed-off-by: Cliff L. Biffle <cliff@oxide.computer>
Change-Id: I222975869b1aa49cc6b1963c79d5ea0f46522b8c
Reviewed-on: http://openocd.zylin.com/5656
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Now that it’s possible to start profiling from either a running or a
halted state, rather than unconditionally halting after profiling
finishes, it makes more sense to restore the processor to whatever state
(running or halted) it was in before profiling started.
Change-Id: If6f6e70a1a365c1ce3b348a306c435c220b8bf12
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5237
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Cortex-M implementation of profiling contains a bunch of
conditionals and checks to handle both chips which have PCSR and chips
which do not. However, the net effect of the non-PCSR branches is
actually exactly the same as what target_profiling_default does. Rather
than duplicating this code, just detect the situation where PCSR isn’t
available and delegate to target_profiling_default.
Change-Id: I1be57ac77f983816ab6bf644a3cfca77b67d6f70
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are a handful of implementations of profiling. There is the
default implementation, which repeatedly halts and resumes the target,
sampling PC each time. There is the Cortex-M implementation, which
uses PCSR if available, otherwise falling back to halting and resuming
and sampling PC. There is the OR1K implementation, which reads NPC
repeatedly. Finally, there is the NDS32 implementation which uses some
kind of AICE commands with which I am unfamiliar.
None of these (with the possible exception of the NDS32
implementation) actually require the target to be halted when starting
profiling. The Cortex-M and OR1K actually resume the target as pretty
much their first action. The default implementation doesn’t do this,
but is written in such a way that the target just flips back and forth
between halted and running, and the code will do the right thing from
either initial state. The NDS32 implementation I don’t know about.
As such, for everything except NDS32, it is not really necessary that
the target be halted to start profiling. For the non-PCSR Cortex-M and
default implementations, there is no real harm in such a requirement,
because profiling is intrusive anyway, but there is no benefit. For
the PCSR-based Cortex-M and the OR1K, requiring that the target is
halted is annoying because it makes profiling more intrusive.
Remove the must-be-halted check from the target_profiling function.
Add it to the NDS32 implementation because I am not sure if that will
break when invoked with a running target. Do not add it to any of the
other implementations because they don’t need it.
Change-Id: I479dce999a80eccccfd3be4fa192c904f0a45709
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5235
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
HWID is a part of 32 bit CONFIGID register. hwid member of struct nrf5_info
was typed uint32_t to enable direct CONFIGID read and masked afterwards.
Change to uint16_t to unify with hwid in struct nrf5_device_spec
and RM description.
Change-Id: Ib720d3ce23c301aee41d074ea78a6f00a23aed68
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5589
Tested-by: jenkins
nRF52 devices indicate a flash error by emitting hard fault
exception (unlike nRF51 series).
Change error message when NVMC READY read fails. A hard fault
from flash erase/write operation is detected here.
Check exit point of the flash write algo to ensure a failed
write is recognised.
Change-Id: I637eda268a6bf45f7f41bcb9dcd82db8f5cb41b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5587
Tested-by: jenkins
nRF51 devices have a clumsy flash protection based on UICR CLENR0.
A code running in RAM can write to a protected flash region without
any hint the protection gets violated.
NVMC flash page erase obeys protection setting but fails absolutely
silently.
Before this change the first problem was not addressed in the code.
To justify the second one, protection was loaded during probe,
after protection setting and after a mass erase.
Move protection updates to the beginning of erase/write operation
and limit them to nRF51 series only. Check for protected sectors
before write.
The change also fixes the problem of 'nrf5 mass_erase' on
nRF52833/840 devices. They use ACL flash protection, which is not
supported in nrf5 driver. mass_erase then looked like it failed.
Change-Id: Ie58cda68eb104d410b02777c3df5b343408e2666
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5522
Tested-by: jenkins
Protection setting has not ever worked. UICR CLENR0 register cannot
be simply written but has to programmed because it resides in UICR
page of the flash.
Enable flash programming before writing CLENR0 and set back to r/o
afterwards.
Inform the user that reset might be required.
Change-Id: Ib0f96c74ba3583ac33f4394ddb57d8c8895adf53
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5586
Tested-by: jenkins
Handle Ctrl+K shortcut which clears the line from the cursor position
to the end of line.
Change-Id: I2ecff5284473cef7c11cf9cb7e1c0c97d55f6c1c
Signed-off-by: Brian Brooks <brooks.brian@gmail.com>
Reviewed-on: http://openocd.zylin.com/5868
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
With help of actionpoint mechanism now it is possible to introduce
watchpoints support for ARC.
Change-Id: I5887335d0ba38c15c377bc1d24a1ef36e138cf65
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5867
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Used jtag_libusb_open from libusb_helper.h instead of
libusb_open_device_with_vid_pid to get device handle,
as well as managing context, i.e. similar to stlink_usb.
Direct calls to libusb1 are left in for the moment.
(When this Gerrit revision was originally created,
the jtag_libusb_ wrappers did not return error conditions.)
Tested w/ a TM4C123GXL board
Change-Id: I71e9a366356c125444d4813e58ddd9b6c6498bf0
Signed-off-by: John Pham <jhnphm@gmail.com>
Signed-off-by: Matthew Trescott <matthewtrescott@gmail.com>
Reviewed-on: http://openocd.zylin.com/2527
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Bit 2 of control register is used if the processor includes the FP
extension
Change-Id: Ie21bc9de8cae5bad9d841e1908eff3aa0bb29d4b
Signed-off-by: Sylvain Chouleur <schouleur@graimatterlabs.ai>
Reviewed-on: http://openocd.zylin.com/5853
Reviewed-by: Sylvain Chouleur <sylvain.chouleur@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The commit b68674a1da ("Upstream tons of RISC-V changes.") was
proposed well before commit 3ac010bb9f ("Fix debug prints when
loading to flash"), but the merge got in different order.
After latest merge, the master branch fails to compile.
Fix the compile error.
Change-Id: Ia3bd21d970d589343a3b9b2d58c89e0c49f30015
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5856
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
These are all the changes from https://github.com/riscv/riscv-openocd
(approximately 91dc0c0c) made just to src/target/riscv/*. Some of the
new code is disabled because it requires some other target-independent
changes which I didn't want to include here.
Built like this, OpenOCD passes:
* All single-RV32 tests against spike.
* All single-RV64 tests against spike.
* Enough HiFive1 tests. (I suspect the failures are due to the test
suite rotting.)
* Many dual-RV32 (-rtos hwthread) against spike.
* Many dual-RV64 (-rtos hwthread) against spike.
I suspect this is an overall improvement compared to what's in mainline
right now, and it gets me a lot closer to getting all the riscv-openocd
work upstreamed.
Change-Id: Ide2f80c9397400780ff6780d78a206bc6a6e2f98
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5821
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Add support for ATSAMG55x19 Rev.B.
Both chips have nearly the same cidr, however, Rev.B has an incremented version.
Change-Id: I5939c41fa5d54c4d3bfb850964974b878f709d13
Signed-off-by: Benedikt-Alexander Mokroß <mokross@gessler.de>
Reviewed-on: http://openocd.zylin.com/5825
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The function adiv5_jim_configure() casts the void pointer
'target->private_config' to a struct adiv5_private_config pointer.
This is tricky in case of aarch64, where the private data are in a
struct aarch64_private_config that has as first element the struct
adiv5_private_config.
While the current solution is working fine, it's not clean and
requires special attention for any further code development.
Override 'target->private_config' to the correct pointer while
calling adiv5_jim_configure().
Change-Id: Ic2fc047dd1e57013943d96e6d5879a919d1eb7b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5847
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Change aarch64 to use ap-num setting if provided. Fall back to original
behavior of using first AP when ap-num is invalid.
Change-Id: I0d3624f75c86ba5fd5a322ac60856dbbb6e71eaf
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5831
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The prescaler computation should round at the nearest integer
value, not to the next integer value.
Change-Id: I957e0774421211f3c4ba4b312738b1c67b87c4a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 051e80812b ("drivers/jlink: fix calculate_swo_prescaler formula")
Reviewed-on: http://openocd.zylin.com/5846
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Search in XDG_CONFIG_HOME as per XDG Base Directory Specification
in addition to $HOME/.openocd.
On Darwin, search in ~/Library/Preferences/org.openocd/ which
appears to be one of the conventional locations.
Make $OPENOCD_SCRIPTS highest priority on all platforms, previously
it was only higher on WIN32.
Update the documentation to reflect the search order.
Change-Id: Ibaf4b59b51fdf452712d91b47ea2b5312bb5ada9
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3890
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Log lines already print a new line, so these superfluous \r\n result in
blank lines being printed in the log. Remove per review comment
request.
Change-Id: I8f5b20776634cf70ce4490fc4f732c916130928a
Signed-off-by: Karl Palsson <karlp@etactica.com>
Reviewed-on: http://openocd.zylin.com/5843
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Remember, don't cast your pointers between types of different sizes!
While the FreeRTOS handlers attempt to account for different pointer and
list widths, the types used are always fixed, so this will _remain_
broken if/when someone targets FreeRTOS on 8/16/64 bit targets. (Note
that this patch does not _change_ that, it was fixed to 32bit before as
well)
In the meantime, this properly handles 32bit reads on a mips BE system
(ath79) as well as remaining fully functional on x86_64.
Change-Id: I677bb7130e25dccb7c1bee8fabaee27371494d00
Signed-off-by: Karl Palsson <karlp@etactica.com>
Reviewed-on: http://openocd.zylin.com/5842
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This driver provides support for Cadence JTAG BFM
The "jtag_dpi" driver implements a JTAG driver acting as a client for the
SystemVerilog Direct Programming Interface (DPI) for JTAG devices.
DPI allows OpenOCD to connect to the JTAG interface of a hardware model
written in SystemVerilog, for example, on an emulation model of
target hardware.
Tested on Ampere emulation with Altra and Altra Max models
Change-Id: Iaef8ba5cc1398ee2c888f39a606e8cb592484625
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5573
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a target is not examined, command vector_catch crashes while accessing
the debug_ap NULL pointer.
maskisr and reset_config commands don't require this check.
Change-Id: I949b6f6e8b983327dd98fbe403735141f8f0b5d6
Signed-off-by: Daniel Trnka <daniel.trnka@gmail.com>
Reviewed-on: http://openocd.zylin.com/5813
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
a) TPIU_ACPR is defined as:
SWO_baudrate = TRACECLKIN/(TPIU_ACPR +1)
b) TPIU_ACPR is set by armv7m_trace_tpiu_config()
target_write_u32(target, TPIU_ACPR, Prescaler-1), so
TPIU_ACPR = Prescaler-1
Replacing TPIU_ACPR in a), we get:
SWO_baudrate = TRACECLKIN/Prescaler, so
c) Prescaler = TRACECLKIN/SWO_baudrate
The Prescaler calculated by calculate_swo_prescaler() is greater by 1:
Prescaler = TRACECLKIN/SWO_baudrate + 1
The second problem is that even in situations when
an exact baudrate match is possible,
the resulting TRACECLKIN/Prescaler already has a 3% deviation.
For example, TRACECLKIN=88000000, SWO_baudrate=500000,
calculate_swo_prescaler will return Prescaler=171.
The correct value should be Prescaler=176 (TPIU_ACPR=175).
Might be related to https://sourceforge.net/p/openocd/tickets/263/
Change-Id: Ib4d6df6e34685a9be4c2995cb500b2411c76e39b
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5807
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32H72x/73x flash is similar to STM32H74x/75x,
except STM32H72x/73x devices have only one single flash bank.
Change-Id: I3d3422dc60234f8273172924f426200210f388cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5792
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
In target/openrisc/jsp_server.c, an error is logged if the ptr was
already NULL. This cannot happen since the pointer was already
referenced few lines before and openocd would have been already
SIGSEGV in that case, so remove the log.
Change-Id: I290a32e6d4deab167676af4ddc83523c830ae49e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5809
Tested-by: jenkins
Change split from http://openocd.zylin.com/5172/ to avoid
conflicts with other pending changes in gerrit.
Change-Id: Id3e21c92b3da7ddce7b00664280da2143c06f172
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5604
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
Change-Id: I2938e333bd1eac5218bd67aefb9d8f373da017a8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5810
Tested-by: jenkins
The prompt pointer in the jtag serial port is never zero'd or allocated.
Completely remove it since there is not much use for it as the target
software will provide the actual prompt.
Change-Id: Id95d8ccb9f725e53b9d03386b11d91eba1cd6ef4
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-on: http://openocd.zylin.com/4093
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: If10a0f1c254aee302b9ca08958390b7f21cdb21b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5824
Tested-by: jenkins
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: Idbc301b34fab19e221131d232577c1629568e6ea
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5823
Tested-by: jenkins
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: I691094a6395acb0e4ea3bea2347ff38379002464
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5822
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
Change-Id: I4de49bf02c9e37b72240224c23fc83abe8a4fa83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5819
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
While there, fix prototype mismatch between header and C file of
the function armv7a_l1_d_cache_inval_virt().
Change-Id: I434bd241fa5c38e0c15d22cda2295097050067f5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5818
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
Change the type of variable retval in 'nor/ambiqmicro.c' to match
both the value to carry and the returned type of the function.
Fix the prototype mismatch of function lpc2900_address2sector()
between the header and the C file.
Change-Id: I68ffba9bd83eec8132f83bff3af993861fd09d84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5816
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
Change the prototype of detect_swo_freq_and_prescaler() in
'jlink.c' to avoid an implicit cast in the caller function.
Change the type of the variable retlen in some functions in
'usb_blaster.c' to properly pass their pointer to the local read
and write functions.
Use the proper parser COMMAND_PARSE_NUMBER(u32, ...).
Change-Id: I5227dbce04ee59881f173724db90790b7b9cc7af
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5815
Tested-by: jenkins
In several cases the 'int' status value returned by libusb and by
aice internal functions is taken in a variable of type 'int32_t',
requiring an implicit (but trivial) cast.
This makes compulsory using 'PRId32' in the format strings that
print such 'int32_t' result and requires an additional implicit
conversion to return the 'int32_t' as 'int'.
Replace to type 'int' all the occurrences of 'int32_t result' and
fix accordingly the format strings.
Plus, all the size of aice commands are stored as int32_t const
variables with uppercase name, violating the coding style, and are
then passed as 'int' parameter to the read/write functions.
Replace the variables with C macros carrying an 'int' value.
While there, replace also a 'uint32_t' loop index with 'unsigned'
and fix the format string in the loop.
Change-Id: Ic57d58770f1af95f003b5a02fbcb7c926ec06fd1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5814
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
While there replace a sequence malloc(size)+memset(,0,size) with a
calloc(1,size).
Replace a pointer assignment to '0' with an assignment to NULL.
In server/*, an error is logged if the ptr was already NULL. This
cannot happen since the pointer was already referenced few lines
before and openocd would have been already SIGSEGV in that case,
so remove the log.
Change-Id: I10822029fe8390b59edff4070575bf7f754e44ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5808
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
There are cases where the pointer is set to NULL after free(), but
then re-assigned within few lines. Drop the setting to NULL when
this is evident. Anyway, the compiler will remove the useless
assignment so no reason to be too much aggressive in this change.
Change-Id: I55b2ce7cbe201410016398933e34d33a4b66e30b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5811
Tested-by: jenkins
Commit 11019a824d ("adi_v5: enforce check on AP number value")
introduces the macro DP_APSEL_MAX and use it in place of hardcoded
magic numbers for the upper limit of AP selection value.
Use the macro also while defining the array of struct adiv5_ap in
struct adiv5_dap.
Change-Id: I88f53ceb710f92a48a8026a365709fbf2d9e6912
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5806
Tested-by: jenkins
All the HLA transports (hla_swd and hla_jtag) register the same
set of commands. Such commands are mainly aimed at handling JTAG
compatibility that is required for the transport hla_jtag only.
Split per transport the command registration and limit the
commands to only those required by the transport itself.
Replace the command "hla newtap" with the transport specific
"swd newdap" or "jtag newtap".
Deprecate the command "hla".
Change-Id: I79c78fa97b707482608516d3824151a4d07644c0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4877
Tested-by: jenkins
A JTAG TAP for boundary scan should be added in the scan chain
through the command "jtag newtap".
In some TCL target script the boundary scan TAP is added through
the command "swj_newdap", command that is inappropriate in this
context because specific for arm adi-v5 SWJ-DP.
This situation was probably created to bypass the error with HLA
framework, caused by missing command "jtag newtap".
Add the command "jtag newtap" in HLA, by reusing the existing
code for command "hla newtap".
Fix the TCL target scripts to use the command "jtag newtap" for
the boundary scan TAPs.
The TCL script target/psoc6.cfg has no evident reference to HLA,
so the reason for using "swj_newdap" is less clear. Nevertheless
it uses the wrong command and, once HLA is fixed, there is no
reason to avoid fixing it too.
Change-Id: Ia92f8221430cf6f3d2c34294e22e5e18963bb88c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4873
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
While loading to flash with debug level at least 3,
OpenOCD tries to print the whole loaded bitstream.
This will be very-very-slow due to implementation of
conversion from buffer to string.
* fix condition on selected debug level in jtag/core.c
* replace slow buf_to_str function from helper/binarybuffer.c
with faster but_to_hex_str function
Change-Id: I3dc01d5846941ca80736f2ed12e3a54114d2b6dd
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
Reviewed-on: http://openocd.zylin.com/5800
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are cases where LOG_*() functions are called before the logs
are initialized with log_init().
E.g. in transport_register() that is executed in gcc constructors,
thus called even before main().
With debug_level set to LOG_LVL_USER=-1 all the LOG_ERROR() get
dropped.
Properly initializing debug_level cause segmentation fault due to
log_output still not initialized.
Initialize debug_level to LOG_LVL_INFO so errors get printed.
Handle separately the case of log_output still NULL, meaning that
log_init() is not called yet.
Change-Id: I2ea32c87a4955fb44e79b38131c456e25dfbc327
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5602
Tested-by: jenkins
The warning message should be printed if the target is NOT halted, not
if it IS halted.
Change-Id: I0a38292a8a2e20e4a4a5ada92b475d551d4cbf38
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5794
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Either of protect and protect_check driver callbacks can be NULL. In
virtual_protect, reuse flash_driver_protect which checks for that case
and generates a nice error message and return code. In
virtual_protect_check, there is no corresponding flash_driver_*
function, so add the NULL check directly.
Change-Id: Ia63d85ede640a8382cf5cad0760f5d1ffe4d7cfe
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5782
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I677bc4487fc2eff2c32e14ca2db5470fddaa63b5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5778
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* use proper type codes
* add 0x in front of hex values
* remove some concatenated empty strings
Change-Id: I06a8344d0ed62de7a0f3e2dd8fba69b17eeb3626
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5783
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There are failure cases of target_create() that are not checked.
Plus, in case of failure the memory allocated in not properly
released before returning error.
Check all the possible failure in target_create().
Change current_target only when target is successfully created.
Add the new target to all_targets list only when target is
successfully created.
Release all the allocated memory before quit on failure.
Use malloc() instead of calloc() for target->type, because the
struct will be fully populated with memcpy().
Change-Id: Ib6f91cbb50c28878e7c73dc070b17b8d7d4e902f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5776
Tested-by: jenkins
If the target is not examined, many internal data required for the
gdb connections are not ready nor allocated. This causes OpenOCD
to hit a segmentation fault.
After the execution of the gdb-attach event handler, check if
target has been examined and eventually return error to refuse the
gdb connection.
Plus, since OpenOCD does not implements non-stop mode yet, gdb
expects the target to be halted by the inferior when the
connection is established.
Print a warning to inform the user in case the target is not
halted, but still accept the gdb connection to permit the
non-intrusive memory inspection with gdb, as explained in
http://openocd.org/doc/html/GDB-and-OpenOCD.html#gdbmeminspect
Change-Id: If727d68f683c3a94e4826e8c62977de41274ceff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5201
Tested-by: jenkins
If a target is not examined when the debugger tries to connect to it
then it can lead to undesired/undefined behavior.
In particular it leads to a zero pointer dereference on the aarch64.
Change-Id: I67f2b714ab8b2727fd36f3de16d7f9017b4c55fe
Signed-off-by: Mikhail Rasputin <mikhail.godlike.rasputin@yandex.ru>
Reviewed-on: http://openocd.zylin.com/5727
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There is no deinit_target method, so few memory allocations leak
at openocd exit.
Issue identified by tracking all calls to arm_dpm_setup().
Implement the method arm11_dpm_deinit() to free all the memory
allocated in arm11_dpm_init() and call it in the new
arm11_deinit_target().
NOT TESTED on real HW.
Change-Id: Icab86e290fc2db14f70eb84c8286357aadb02a35
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5694
Tested-by: jenkins
By default GDB timeouts after 2 seconds, even if this value can be
modified with GDB command "set remotetimeout".
On OpenOCD side, the default event for GDB attach is to halt the
target and wait it to halt. But here the default timeout of the
halt command is 5 seconds!
If the target cannot be halted (e.g. it's kept in reset by another
core or the debugger doesn't have enough privileges) then GDB will
timeout while OpenOCD is still waiting and is unable to
communicate with GDB.
Decrease the halt timeout to 1 second in the default GDB attach
event handler.
Change-Id: I231c740816bb6a0d74b0bc679a368a6cbfb34824
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5687
Tested-by: jenkins
Implementation largely taken from Nuvoton github
https://github.com/OpenNuvoton/OpenOCD-Nuvoton
Reset is still not fully compatible with OpenOCD framework.
Adapted to hidapi.
Change-Id: Ieb1791b1b7f0b444c15c9668f8f2bcf34975d48f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Reviewed-on: http://openocd.zylin.com/5720
Tested-by: jenkins
Reviewed-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Marc Schink <dev@zapb.de>
this flash is used on the Digilent CMODA7 FPGA board
Change-Id: I6749ca3fbebf2e384051a26a3fd253da5d6e25fb
Signed-off-by: Michael Betz <michibetz@gmail.com>
Reviewed-on: http://openocd.zylin.com/5787
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add support for Nu-Link1 over usb hidapi and config file.
The original work is fetched from Nuvoton github.
Code cleanup, fix merge conflicts, compile and runtime issues.
Switch the code from libusb to hidapi, being the device HID based.
Add documentation.
Merge fixes for multi-word memory read.
Reset is not fully compatible with openocd framework; currently
the target is reset and then halt at openocd start.
Change-Id: I9738de4e26783ba462ea3e39ec32069fd5bb7d94
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5635
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
This commit fixes support for the nEDBG CMSIS-DAP interface
which is used ie. on the Curiosity Nano SAMD21 board.
nEDBG, similarily to mEDBG, does not support 512 byte HID packets.
This patch adds its USB PID to the exclusion list to make sure that
we stick with the default 64 bytes.
Change-Id: I9010b0cf77c0b1347269a759b5d16ee5155abb16
Signed-off-by: Michal Potrzebicz <michal@elevendroids.com>
Reviewed-on: http://openocd.zylin.com/5756
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The blinking was implemented for JTAG only.
Extend it to SWD.
There is no error check on SWD exchange. Add a FIXME for further
fix.
Change-Id: I42a6708c54b1eefaf691e0fe09ca58c42b2764fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5771
Tested-by: jenkins
Bitbang interface allows having a LED on one of the GPIO.
Let also linuxgpiod driver to specify and use the LED connection.
Change-Id: Id3d8772ee1808b92354fd073ba3947bacd8253ef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5770
Tested-by: jenkins
Fix typos and duplicated words in comments and strings.
Change-Id: I64282c7018462deefeeb8e5f4d0d81942425b3fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5758
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
There is no method to free the register cache, allocated in
arm720t_init_target().
Issue identified by tracking all calls to arm7tdmi_init_target().
Implement the method arm720t_deinit_target() by calling directly
arm7tdmi_deinit_target().
NOT TESTED on a real arm720t target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a xscale:
sed -i s/arm926ejs/arm720t/ tcl/target/spear3xx.cfg
Change-Id: I53c1f46c1a355a710e8df01468b19220671569dc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5697
Tested-by: jenkins
There is no method to free the register cache, allocated in
arm7tdmi_init_target(), so we get a memory leak.
Issue identified by tracking all calls to arm_build_reg_cache().
Implement the method arm7tdmi_deinit_target() that in turn calls
arm7tdmi_free_reg_cache().
NOT TESTED on a real arm7tdmi target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a arm7tdmi:
sed -i s/arm926ejs/arm7tdmi/ tcl/target/spear3xx.cfg
Change-Id: Iad465b708eb4ebb298725d7155fea76357e9045c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5696
Tested-by: jenkins
There is no method to free the register cache, allocated in
xscale_build_reg_cache(), so we get a memory leak.
Issue identified by tracking all calls to arm_build_reg_cache().
Implement the method xscale_deinit_target() that in turn calls the
new xscale_free_reg_cache().
Fix leak of struct xscale.
NOT TESTED on a real xscale target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a xscale:
sed -i s/arm926ejs/xscale/ tcl/target/spear3xx.cfg
Change-Id: Ibb2104c42411b76f4bb77c2fa387d1b85a3d2d5d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5695
Tested-by: jenkins
Similarly to the fix for arm926ejs (also base on arm9tdmi), fix
the other targets based on arm9tdmi.
The fix for arm926ejs is tested on SPEAr320 target.
This fix is proposed separately because is not tested on a correct
target device, but tested on SPEAr320 by hacking the target type
and pretending it is the correct one, e.g.:
sed -i s/arm926ejs/arm920t/ tcl/target/spear3xx.cfg
The memory leaks detected and fixed are:
- arm register cache;
- EmbeddedICE register cache;
- arm_jtag_reset_callback internal data;
- struct <target_type>_common.
Change-Id: I565f9a5bf144a9df78474434d86a64127ef0fbe5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5699
Tested-by: jenkins
Add threads support for RIOT (https://github.com/RIOT-OS/RIOT).
Original code is from Daniel Krebs.
Change-Id: I83fe3b91dd75949e800b5aea1015d8fa37b09c61
Signed-off-by: Daniel Krebs <github@daniel-krebs.net>
Signed-off-by: Vincent Dupont <vincent@otakeys.com>
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Reviewed-on: http://openocd.zylin.com/4256
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* use proper type codes
* add 0x in front of hex values
* remove some concatenated empty strings
Change-Id: I77e8dd161887f02ecf8019b43d3e8e7cc122ad0e
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5780
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Actionpoint mechanism allows to setup HW breakpoints and watchpoints on Synopsys ARC CPUs.
This mechanism is controlled by DEBUG register and by a set of auxilary registers.
Each actionpoint is controlled by 3 aux registers: Actionpoint(AP) match mask(AP_AMM),
AP match value(AP_AMV) and AP control(AC).
Note: some fields of actionpoint_t structure will be used in further
support of watchpoints.
Change-Id: I4efb24675f247cc19d9122501c9e63c3126fcab4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The adapter NXP LPC-Link2 is a USB composite device that provides
five interfaces; among three of them that are of HID class, only
one is cmsis-dap.
Accordingly to ticket 255, OpenOCD code is not opening the right
HID interface; then it fails to communicate with the cmsis-dap
while checking the adapter's info.
Unfortunately, hidapi does not provide any support for reading the
string descriptor of the interface, otherwise it would have been
trivial to look for the right cmsis-dap interface.
In fact the cmsis-dap specification reports:
The CMSIS-DAP Firmware can be also part of a USB composite
device. If this case, the HID Interface String must
contain the sub-string CMSIS-DAP.
This requirement is satisfied by the USB device descriptor of the
LPC-Link2 reported below, but cannot be used.
Add a quirk to let OpenOCD only accept interface number zero on a
LPC-Link2 device.
Bus 001 Device 050: ID 1fc9:0090 NXP Semiconductors
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x1fc9 NXP Semiconductors
idProduct 0x0090
bcdDevice 1.00
iManufacturer 1 NXP Semiconductors
iProduct 2 LPC-LINK2 CMSIS-DAP V5.224
iSerial 3 I3F4AABA
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x00ab
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 4 LPC-LINK2 CMSIS-DAP V5.224
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 35
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 4
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 7 LPC-LINK2 DATA PORT
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 35
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 1
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 1
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 0
iFunction 5 VCOM
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 5 VCOM
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x01
call management
bDataInterface 2
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 1
bSlaveInterface 2
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 5 VCOM
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 6 LPCSIO
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 33
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 2
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 2
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Change-Id: Ib3d46f87743a2d35a266842cb356035d898d466e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Masatoshi Tateishi <tateishim3@gmail.com>
Reported-by: Donald Bailey <donaldb@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/255/
Reviewed-on: http://openocd.zylin.com/5732
Tested-by: jenkins
The code in cmsis_dap_usb_open() already searches for the right
HID device that corresponds to the adapter. By calling hid_open()
it asks hidapi to re-search the adapter again based on the VID:PID
and the serial string of the adapter it has just found!
Apart from being a run-time overhead, this has an additional
drawback; there are USB adapters built as composite USB devices
that, beside the cmsis-dap HID interface, have other HID
interfaces for other purposes.
A typical example is the NXP LPC-Link2, that over the 5 interfaces
0) cmsis-dap (HID)
1) VCOM-CDC
2) VCOM-CDC
3) LPCSIO (HID)
4) LPC-LINK2 DATA PORT (HID)
has 3 of them of HID class.
The code in cmsis_dap_usb_open() could select the right interface
but then cannot propagate this information to hid_open().
Replace the call to hid_open() with hid_open_path(), passing as
parameter the "unique" path of the HID device already found.
Checking in hidapi source code, the implementation of hid_open()
consists in enumerating the HID devices, scan for the first one
matching VID:PID and serial number, and opening it by calling
hid_open_path(). This analysis highlights that using directly
hid_open_path() should not introduce any regression.
While applying these changes, move hid_init() before enumerating
the HID devices. This has no real consequences because the HID API
is marked as optional but, logically, it should be called before
any other HID API.
Change-Id: I77ec01dca64223ec597f21f188f363366d0049c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Masatoshi Tateishi <tateishim3@gmail.com>
Reviewed-on: http://openocd.zylin.com/5731
Tested-by: jenkins
The function perror() sends the output to stderr, but OpenOCD
cannot intercept such output to send it to the log.
Replace all occurrences of perror() with LOG_ERROR(), but keeping
the same output format of perror().
The replacement is done automatically through:
sed -i 's/perror("\([^":]*\)[: ]*")/LOG_ERROR("\1: %s", strerror(errno))/' src/jtag/drivers/*.c
Change-Id: I4c140bdb09235d56cfd8bef75da9b56fbe7c2aec
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5728
Tested-by: jenkins
New adapter driver for GPIO bitbanging over Linux GPIO descriptors
through the library libgpiod.
On Debian based distribution, the package libgpiod-dev is required
for build.
Change-Id: I1ce1a4f1ca79096d6d476b01b523c8c10f2cac07
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5559
Tested-by: jenkins
If the configuration file specifies both SWD and JTAG gpios, the
current code request all of them. In case of overlap a warning is
generated when the same gpio is released for the second time.
Require and release only the gpio needed by the specified
transport.
Change-Id: I41a0970980ceeb559afa98ab34cfe93dffed2e1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5556
Tested-by: jenkins
The split in OpenOCD between SWD and JTAG has been already fully
implemented. The bitbang driver still keeps a single API write()
to drive the output lines.
Introduce a new SWD specific API swd_write().
Move the existing SWD bitbang drivers to the new API by extracting
the available conditional implementation.
Cleanup some function prototype.
Remove the now unused global swd_mode, handled implicitly.
Rename bitbang_exchange() as bitbang_swd_exchange() to track its
scope for SWD only.
Change-Id: Ie53080b941cb1ac7a34a1f80bad8bee4e304454d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5555
Tested-by: jenkins
The SWD framework already takes care of switching between JTAG and
SWD by calling driver's switch_seq() in swd_connect() and in
swd_quit(); there is no need for the driver to force the switch
again.
Remove the extra switch between jtag and swd.
Change-Id: I84de4bffb593374b96fce31951c6cc83f92d2578
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5554
Tested-by: jenkins
Kinetis Flash Configuration Field needs special handling to prevent unwanted
locking of the device. Warn user about any difference between generated
FCF and FCF data in the programmed file. Inform user that re-programming
of already programmed FCF may fail on devices with FTFE flash module.
While on it remove useless setting of is_erased flag after erase.
Change-Id: I3911f436674547fa12ef3886c7d5e8cd889f9e2b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Fixes: https://sourceforge.net/p/openocd/tickets/270/
Reported-by: Noel Diviney <vk3avm@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/5753
Tested-by: jenkins
Since e22c6484ea the trial/error allocation shows
"not enough working area available(requested 2048)" message
on klx.cfg. The message is not clear if it means a problem or not.
Replace with new style allocation using target_get_working_area_avail()
Change-Id: I87fe1e38248fcac29982b72aaba12217a0552f38
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5752
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
In case of GDB connection not using extended mode, issue a warning
message to suggest the user to switch using the extended mode.
Issue the message only once at each run of OpenOCD, to avoid too
much noise.
Update the documentation to suggest using extended mode.
Change-Id: I9326e84f748d5d7912d5a48f00f0fb541ca19221
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5311
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_ARGUMENTS -f {} \;
This patch also fixes an incorrect function prototype in zy1000.c.
ZY1000 minidriver implementation overrides the function
arm11_run_instr_data_to_core_noack_inner(), but the prototype is
not the same as in src/target/arm11_dbgtap.c and to avoid compile
error it was changed also the prototype of the called function
arm11_run_instr_data_to_core_noack_inner_default().
Change-Id: I476cda8cdb0e1e280795b3b43ca95c40d09e4a3d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5630
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The checkpatch script from Linux kernel v5.1 complains about using
space before comma, before semicolon and between function name and
open parenthesis.
Fix them!
Issue identified using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SPACING -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: I1062051d7f97d59922847f5061c6d6811742d30e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5627
Tested-by: jenkins
It is an error to prefix with "0x" the print of values in decimal.
Replace the incorrect decimal format specifier with PRIx32.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types PRINTF_0XDECIMAL -f {} \;
Change-Id: I2eb867ef654527b2737ba573a405ec8f97c6a739
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5624
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Current hla driver supports two "layout": stlink and ti-icdi.
The configure script allows to independently enable/disable the
the two layout. But in reality by selecting only one of them the
whole hla driver is built, including both "layouts".
This is currently not a big issue because the dependencies of the
two layout are the same (libusb), so we are sure that selecting
one of them would permit to build both.
This is going to change with the merge of a third "layout" for
Nuvoton Nu-Link, because it would be based on hidapi.
We need, at least, to decouple the build of libusb and hidapi
"layouts". A full decouple of each "layout" is also welcome to
match the selection done during configure.
Introduce a new automake macro for each of the two "layout" and
use them to conditionally build the "layout" files.
Use the existing autoconf macros to conditionally compile the code
that depends by the "layout".
Change-Id: Ia20da7a260002a8d2af883425aa401b8920d3f36
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5719
Tested-by: jenkins
Change-Id: Ib9c567e2287f2a99172bd3bd35a81e3205cea421
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5749
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Jim_SetResultFormatted() frees jim object earlier and the
Jim_FreeNewObj() does it second time. It breaks the memory heap.
To avoid it the Jim_IncrRefCount() + Jim_DecrRefCount() should be used
instead of the Jim_FreeNewObj() call.
Change-Id: Ifa5f38009b2d617624b5f27e916720888a3dbad9
Signed-off-by: Mikhail Rasputin <mikhail.godlike.rasputin@yandex.ru>
Reviewed-on: http://openocd.zylin.com/5724
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use 'unsigned int' and 'bool' instead of 'int' where appropriate.
While at it, fix some coding style issues.
No new Clang analyzer warnings.
Change-Id: I700802c9ee81c3c7ae73108f0f8f06b15a4345f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4929
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to the datasheet, erasing a block can take up to 200 ms.
When using a Segger J-Link with a 2 MHz clock the current loop
finishes after < 50 ms, ignores the timeout, and then fails when
erasing the next block.
Switch to a time based check, add an explicit yield, and report an
error on timeout.
Change-Id: I8255401d1e59f427a08d2cccb8a66143dcdbb324
Signed-off-by: Michael Hope <mlhx@google.com>
Reviewed-on: http://openocd.zylin.com/5706
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Before commit b3ce5a0ae5 ("target: use LOG_USER to print errors
in events") an error in an event handler was silently lost, while
now the associated message is printed out.
A "shutdown" command in a target event (e.g. in gdb-detach) causes
the event to end with error code ERROR_COMMAND_CLOSE_CONNECTION,
that triggers the error message:
shutdown command invoked
Error executing event <event-name> on target <target-name>:
The error code returned by the command "shutdown" is required to
stop the execution in a script/proc and avoid executing any
further command in the script/proc.
It is then normal to get an error code from the "shutdown" command
and it should not be printed out.
Intercept the return code of the event in case of "shutdown", then
skip scheduling other target events and return without printing
the incorrect error message.
Change-Id: Ia3085fb46beacb90a5e4bf0abf7c6e28bb9e6a9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Laurent Lemele <laurent.lemele@st.com>
Reviewed-on: http://openocd.zylin.com/5710
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Add support for SWD debug to the Xilinx XVC/PCIe driver.
This is possible since the device is essentially a shift-register.
So doing SWD vs JTAG is a matter of wiring things correctly on the
RTL side (use TMS for SWDI, TDO for SWDO).
The clang static checker doesn't find any new problems with this change.
Change-Id: I3959e21440cd1036769e8e56a55e601d3e4aee9a
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5447
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this commit we introduce L1 and L2 cache
flush and invalidate operations which are necessary for
getting/setting actual data during memory r/w operations.
We introduce L2 cache support, which is not presented
on currently support EMSK board. But L2 is presented
on HSDK board, which soon will be introduced.
Change-Id: I2fda505a47ecb8833cc9f5ffe24f6a4e22ab6eb0
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5688
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When debugging an ARMv8-A/AArch32 target running HYP mode, OpenOCD would
throw the following error to GDB on most operations (step, set breakpoint):
cannot read system control register in this mode
The mode in question is 0x1A, a privilege level 2 mode available on cores
that have the virtualization extensions (such as the Raspi 3).
Note: this mode is only used when running in AArch32 compatibility mode.
Signed-off-by: Lucas Jenss <public@x3ro.de>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Change-Id: Ia8673ff34c5b3eed60e24d8da57c3ca8197a60c2
Reviewed-on: http://openocd.zylin.com/5255
Tested-by: jenkins
Reviewed-by: Lucas Jenß <lucas.jenss@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This update is for testing the upcoming 0.2.0 release.
Change-Id: I400b09eb3ead4306c83c7980c621124101aaef7e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5723
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This fixes a regression introduced in "2dc88e1479f29ef0141b05bfcd907ad9a3e2d54c"
Change-Id: I04dc19ed30118a4c499b83732700b2ee0fdb67b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5610
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The current version erroneously allows any number of arguments >= 1.
Change-Id: I64156c11b48d411c72bebbf866954818cd036ff2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5716
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Issue: server_quit is called before adapter_quit:
In WIN32 only in server_quit we do an WSACleanup,
which terminates/closes all active sockets.
So if the adapter is TCP based, the adapter.quit handler
will fail if it will need to send some commands through TCP.
Example: close_socket in jtag_vpi_quit will fail in WIN32
because the socket is already closed
and the errno is set as "Bad File Descriptor"
To fix that we introduced new functions called server_host_os_entry/quit
to manage specific OS setup (hence WSA for sockets in WINDOWS) in order
to delay WSACleanup after adapter_quit().
Change-Id: Ie4afacafe123857f6ae300e376bdfcf0d8c027ac
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5456
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MULTILINE_DEREFERENCE -f {} \;
Change-Id: Icba05613e22a72ecc3e6a0aad7cb6b479496146f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5629
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
If the function parse_u64() fails, we jump to return, thus leaking
the memory just allocated in 'v'.
Issue identified by clang.
Move earlier the call to parse_u64() and the associated test,
before memory allocation.
While there, fix a possible NULL pointer dereferencing in case the
calloc() fails, by testing for allocation failure.
Change-Id: I6a77ee17aceb282bbdfefe7cdafeba2e0e7012f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5692
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
