Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:
- Recent rev C lm3s811 eval boards didn't work. They must use
the ICDI layout, which sets up some signals that the older
boards didn't need. This is actually safe and appropriate
for *all* recent boards ... so just make "luminary.cfg" use
the ICDI layout.
- "luminary-lm3s811.cfg", was previously unusable! No VID/PID;
and the wrong vendor string. Make it work, but reserve it
for older boards where the ICDI layout is wrong.
- Default the LM3748 eval board to "luminary.cfg", like the
other boards. If someone uses an external JTAG adapter, all
boards will use the same workaround (override that default).
The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it. Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This config is only lightly tested, and doesn't work well yet;
but it's a start.
* Notably missing is PLL configuration, since each DaVinci
does that just a bit differently; and thus DDR2 setup.
* The SRST workaround needed for the goof in the CPLD's VHDL
depends on at least the not-yet-merged patch letting ARM9
(and ARM7) chips perform resets that don't use SRST.
So this isn't yet suitable for debugging U-Boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates the board configuration for the SAM9-L9260 board with the
configuration for the on-board NAND and dataflash. Included are commands
for configuring the AT91SAM9 NAND flash driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove more remnants of the old "jtag_device" syntax.
Don't [format "%s.cpu" $_CHIPNAME] ... it's needless complexity.
Remove various non-supported "-variant" target options; they're not
needed often at all.
Flag some of the board files as needing to have and use target files
for the TAP and target declarations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename the "armv4_5" command prefix to straight "arm" so it makes
more sense for newer cores. Add a simple compatibility script.
Make sure all the commands give the same "not an ARM" diagnostic
message (and fail properly) when called against non-ARM targets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
General rule, this is all board-specific and doesn't belong
in target config files. Some of these were just cosmetic.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's been about a year since these were deprecated and, in most
cases, removed. There's no point in carrying that documentation,
or backwards compatibility for "jtag_device" and "jtag_speed",
around forever. (Or a few remnants of obsolete code...)
Removed a few obsolete uses of "jtag_speed":
- The Calao stuff hasn't worked since July 2008. (Those Atmel
targets need to work with a 32KHz core clock after reset until
board-specific init-reset code sets up the PLL and enables a
faster JTAg clock.)
- Parport speed controls don't actually work (tops out at about
1 MHz on typical HW).
- In general, speed controls need to live in board.cfg files (or
sometimes target.cfg files), not interface.cfg ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The semantics of "-work-area-virt 0" (or phys) changed with
the patch to require specifying physical or virtrual work
area addresses. Specifying zero was previously a NOP. Now
it means that address zero is valid.
This patch addresses three related issues:
- MMU-less processors should never specify work-area-virt;
remove those specifications. Such processors include
ARM7TDMI, Cortex-M3, and ARM966.
- MMU-equipped processors *can* specify work-area-virt...
but zero won't be appropriate, except in mischievous
contexts (which hide null pointer exceptions).
Remove those specs from those processors too. If any of
those mappings is valid, someone will need to submit a
patch adding it ... along with a comment saying what OS
provides the mapping, and in which context. Example,
say "works with Linux 2.6.30+, in kernel mode". (Note
that ARM Linux doesn't map kernel memory to zero ...)
- Clarify docs on that "-virt" and other work area stuff.
Seems to me work-area-virt is quite problematic; not every
operating system provides such static mappings; if they do,
they're not in every MMU context...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Config for Intel's "Lubbock" PXA255 development board. Even more
so than the PXA255 itself, this is obsolete. AFAIK this was the
first generally available development platform for PXA255. Intel
stopped providing these after other devel boards became available.
One interesting thing about this board from the OpenOCD perspective
is probably its flash configuration. Each bank is 32 bits wide,
built from two 16-bit StrataFlash chips wired in parallel. This
doubles throughput ... it reads/writes 32 bits in the time a single
chip takes to write just 16 bits.
This conf mostly works, given XScale bugfixes, but has some issues
(notably: no access to the on-board SDRAM) flagged by FIXMEs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This is the very basic board config for the balloon3 board cpu JTAG
channel.
The rest of the config comprises another 14 .cfg files which I suspect
openocd doesn't really want all of. I'm still not sure how to deal
with this. I'll post another mail/patch to discuss.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Ofrwarded from Ron, who's not subscribed.
----- Forwarded message from Ron <ron@debian.org> -----
From: Ron <ron@debian.org>
Date: Wed, 14 Oct 2009 04:50:17 +1030
To: wookey@debian.org
Subject: [PATCH] OpenRD board configuration
X-Spam-Status: No, score=-3.6 required=4.5 tests=BAYES_00,RCVD_IN_DNSWL_LOW
autolearn=ham version=3.2.5
This piggybacks on the 'sheevaplug' layout which uses the same Kirkwood SoC.
Signed-off-by: Ron Lee <ron@debian.org>
This is clearly noted in the hardware spec (section 5.2.3); it
works around a chip erratum: "If the MPU_RESET signal is used,
it may cause the EMIFS bus to lock."
I seem to have a board with such an initial build. The chip
is labeled XOMAP. Presumably, parts without that "X" prefix
(eXperimental) resolve this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Update the board config for the DaVinci DM355 EVM so the reset-init
event handler does the rest of the work it should do:
- minor PLL setup bugfixes
- initialize the DDR2 controller
- probe both NAND banks
- initialize UART0
- enable the icache
git-svn-id: svn://svn.berlios.de/openocd/trunk@2699 b42882b7-edfa-0310-969c-e2dbd0fdcd60
defining ntrst_delay is pointless; don't.
At least the LM3S3748 eval board doesn't need nsrst_delay
either; remove that too.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2645 b42882b7-edfa-0310-969c-e2dbd0fdcd60
